21
parts must be correctly installed and fulfil all conditions
to ensure perfect operation of the saw
−
Damaged guards and parts
must be properly repaired
or exchanged by a recognized, specialist workshop;
insofar as nothing else is stated in the instructions for
use.
−
Damaged or illegible
security labels
have to be
replaced.
Do not allow any tool key to be plugged in
!
Before switching on, check always that wrenches and
adjusting tools are removed.
Store
unused equipment
in a dry, locked place out of the
reach of children.
Electrical safety
Design of the connection cable according to IEC 60 245 (H
07 RN-F) with a core cross-profile section of at least
−
1.5 mm2 for cable lengths
up to
25m
−
2.5 mm2 for cable lengths
over
25m
Long and thin connection lines result in a
potential drop
.
The motor does not reach any longer its maximal power; the
function of the device is reduced.
Plugs
and
coupler outlets on connection cables
must be
made of rubber, non-rigid PVC or other thermoplastic
material of same mechanical stability or be covered with this
material.
Protect yourself against
electric shocks
. Avoid touching
earthed parts with your body.
The connector of the connection cable must be
splash-
proof
.
Wind off completely the cable when using a cable drum.
Do not use the
cable
for purposes for which it is not meant.
Protect
the cable against
heat, oil and sharp edges
. Do
not use the cable to pull the plug from the socket.
Regularly check
the saw cable and if damaged, have it
renewed
by a recognised skilled electrician.
When running the
connection line
observe that it does not
interfere, is not squeezed, bended and the plug connection
does not get wet.
Regularly check the
extension cables
and replace them if
they are damaged.
Do not use any defective connection cables
.
When working outdoors, only use extension cables
especially
approved
and appropriately labelled for outdoor
use.
Do not set up any provisional electrical connections
.
Never bypass
protective devices or deactivate them.
Only hook up the machine by means of a f
ault-current
circuit breaker
(30 mA).
The
electrical connection
or
repairs
to electrical parts of
the machine must be carried out by a certified electrician
or one of our customer service points. Local regulations –
especially regarding protective measures – must be
observed.
Repairs
to other parts of the
machine
must be carried out
by the
manufacturer
or one of his customer service
points.
Use only original spare parts and accessorie parts
.
Accidents can arise for the user through the use of other
spare parts. The manufacturer is not liable for any damage
or injury resulting from such action.
Assembly of the saw
A1
A2
A3 A4
Unfold the stand (16).
1.
Bring the frame stand together so that the lock is released.
2.
Pull up the frame until it latches again.
3.
Install the additional braces (36, 37) on the stand (36 – short
brace , 37 – long brace)
B1
B2
Install the transport wheels (18).
C
Turn the saw around. You can align the saw by turning the
adjusting foot (17) in or out.
Install splitting wedge
D1
1.
Turn the screw out.
2.
Place the screwdriver in the hole to take out the table insert
(6).
D2
Raise the saw blade (22) to its highest position.
D3
Loosen the screw on the clamp.
D4
Insert the splitting wedge (23) between the pressure plate (33)
and the counter-plate (34).
D5
1.
Adjust the splitting wedge (23). The distance between the
saw blade and splitting wedge must be max. 5 mm.
2.
Retighten the screw on the clamp.
D6
1.
Reinsert the table insert (6).
2.
Stand behind the saw, insert the screwdriver in the hole and
pull it towards you so that the table insert latches in place.
3.
Retighten the screw for attaching the table insert.
E
Attach the safety guard (5) using an M6 x 40 coach bolt and an
M6 wing nut on the splitting wedge (23).
F1
F2
Screw both holders (27 and 28) on.
Install bench length extension
G1
Attach the bench length extension (1) using the two hex head
screws M6 x 12.
G2
G3
Attach the supports (24) to the bench length extension (1) using
two hex head screws M6 x 12, washers A 6,4 and M6 hex nuts.
