manualshive.com logo in svg

ATI Technologies Q45D, Руководство пользователя

Поделиться
Скачать
ATI Technologies Q45D Скачать руководство пользователя страница 15

 ATI 

Q45D Portable Dissolved Oxygen  

Part 5 

– Operation

 

 

(REAR OF ENCLOSURE)

DC BATTERY BOARD

POWER CABLE

 

Figure 8 - Battery Board Connections 

 

The  first 

(S1)

  is  an  On/Off  slide  switch.    This  switch  must  be  in  the  ON  position  for  operation.  

Turn it to OFF if you do not intend to operate the monitor in the next week or two. 
 
The second switch assembly 

(S2)

 contains two switches, the one on the left marked LOCK and 

the one on the right marked MODE.  The function of these two slide switches are as follow: 
 

LOCK

 

This switch is used to define how the monitor will turn on and off.  This switch is 
normally in the OFF position.  With the lock switch off, the monitor will be turned 
on  manually  using  the  MENU  key  on  the  front  of  the  monitor.    With  the  lock 
switch  in  the  ON  position,  the  monitor  will  always  be  on  when  there  is  enough 
power to run the monitor.  The ON position is normally used when operating from 
an external power supply intended for continuous operation.   

 

MODE

 

This switch is used to set the voltage at which monitor will shut off when powered 
by  internal  batteries.    Alkaline  batteries  can  normally  be  run  down  to  about  0.8 
volts.  When  using  alkaline  batteries,  the  mode  switch  is  in  the  OFF  position 
(factory  default).    If  rechargeable  NiMH  batteries  are  substituted,  place  the 
MODE  switch  in  the  ON  position.    Note  that  rechargeable  NiMH  batteries  have 
only about 35% of the capacity of an alkalines.  However

, 

NiMH batteries can be 

recharged hundreds of times. 

 

The third switch assembly is a single slide switch 

(S3)

 which defines whether the 

0-2.5 VDC signals from the monitor are isolated or non-isolated.  Output isolation 
is not required when outputs are connected to the internal data logger.  However, 
if the outputs are connected to external devices through the external connection 
cable, putting this switch in the ISO position will protect against possible ground 
loops.    The  isolation  circuit  will  slightly  increase  the  power  requirement  for  the 
monitor, resulting in a bit less battery life.  

Содержание Q45D









































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды