Atek ALC 77-C Скачать руководство пользователя страница 4 | Manualshive

Страница: 4 / 19

Atek ALC 77-C Скачать руководство пользователя страница 4

+

-

+

-

-

L

N

Supply Voltage
24 VAC / DC or
85 / 265 VAC

GND

+5 Vdc or +12 Vdc

A Input of Counting

Signal

girişi

B Input of Counting Signal

Z Input of Reset

Signal

girişi

Input of Hold
Signal

girişi

TX

RX

GND RS

-2

32

These outputs are optional.
These terminals are open,
if is not specified when
ordering
.

CO
M

NO

NC

CO
M

NO

NC

OUT

2

OUT

1

Ground of Sensor

ucu

Ground

SAFETY WARNINGS

1.

Follow the instructions and warnings in the user guide.

2.

Please check the type of power supply before connects energy to the device.

3.

Please the device mounted on panel against dangers of fall, snap, shake during working.

4.

Make Sensor connections without energy on the device; do not connect in any way during

operation.

5.

Make sure that is shielded cables between device and sensor.

6.

Do not leave the device exposed to a heat source (solar, heater etc.)

7.

ALC77 industrial control device is not suitable for use in the external environment, Use only

room conditions.

8.

Wipe with a damp cloth to clean the device, do not use water, thinner etc.

9.

Comply with the limit values specified in the technical specifications for relay outputs.

10.

The device cannot be changed by the user in the event of a fault, Please contact our technical

service in case of failure.

2. CONNECTIONS

- 2 -

1

2

3

4

5

6

7

8

9

10

11

12

13

14

15

16

17

18

19

20

21

22

«
...
2
3
4
5
6
...
»

Содержание ALC 77-C




















Отзывы:

Нет отзывов