F.2.
Tighten the Yoke connection to suit the
weight of your display.
F.1.
Attach your Display using the
provided M4 Screws.
4xM4
Screws
6mm Allen Key
75 or 100
F Connect your Display
Note: It is recommended that at least two people carry out this operation.
Your Telehook Articulated Arm or Swing Arm is now complete. See Step J for installing Cable Management.
D Swing Arm Assembly
E Articulated Arm Assembly
Assemble the Swing Arm as
Illustrated.
- Select the appropriate VESA
plate (75/100mm or 200mm) to
suit your display.
- Connect VESA Plate as shown
and tighten M8 Cap Screw.
- Adjust Display Tilt when fitted.
(Refer to diagram F.2)
- Install Push-In Clips for cable
management.
Assemble the Articulated Arm
as Illustrated.
- Select the appropriate VESA
plate (75/100mm or 200mm) to
suit your display.
- Connect VESA Plate as shown
and tighten M8 Cap Screw.
- Adjust Display Tilt when fitted.
(Refer to diagram F.2)
- Install Push-In Clips for cable
management.
6mm Allen Key
75/100mm
VESA Plate
M8 Cap Screw
M8 Nyloc (x2)
Push-In
Clips (x3)
M8 Square
Neck Bolt (x2)
Yoke
One Sided
Bush (x4)
200mm
VESA Plate
OR
Primary Arm
6mm Allen Key
75/100mm
VESA Plate
M8 Cap
Screw
M8 Nyloc (x3)
Push-In
Clips (x3)
M8 Square
Neck Bolt (x2)
Yoke
One Sided
Bush (x4)
200mm
VESA Plate
OR
Primary
Arm
M8x115mm
Bolt
Secondary Arm
Steel
Washer (x2)
Plastic
Washer (x2)
D.1.
E.1.
As TFT Manufacturers are constantly releasing new monitor models, Atdec does not accept responsibility if the VESA mounting does not comply with the international standards. Due to continuing product development, the
manufacturer reserves the right to alter specifications without notice. Published: 01.09.05
c
G Attach the VESA Plate to your Display.
Select the appropriate VESA plate (75/100mm or 200mm) to suit your display, and connect as shown.
Your Telehook Multi is now complete and ready to use.
J Installing Cable Management
J1
Ensure Push In Clips have been fitted. Note; They
can be used in either the top or the bottom face
of each Arm and the Cover Plate.
Attach Cables to the Telehook Multi using the Push In
Clips
J2
H Install the Wall Bracket
I Attach your Display
Note: It is recommended that at
least two people carry out this operation.
or
M4 Screws (x4)
75 or 100
Install The Mount Bracket Horizontally as shown.(Use Spirit
Level) Use optional stud mounting holes for mounting to a
single stud. Refer to Step C. for further detailed wall fixing
instructions.
2x14 Gauge
Coach Screws
(Choose which
Mounting Holes)
Cover Plate
Wall Bracket
Attach your Display as
shown.
Using an extendable
Socket Wrench, firmly
tighten the connection
to suit the weight of
your display.
M8 Nyloc
M8 Square
Neck Bolt
200mm VESA
Plate
M4 Screws
(x6)
Option 3 (Wall Mount)
Note: You will require an extendable socket wrench during installation.
Your Telehook Wall Mount is now complete. See Step J for installing Cable Management.
Push-In Clip
Optional Stud
Mounting holes
For easier installation of larger monitors (23” to 30”), it is recommended that the Swing Arm (Option.1.) be used as
an alternative to the Wall Mount.
G.1.
G.2.
I.1.
H.1.
