background image

 

   

                                                                                        

wwwAtairCanopies.com

 

 

 

Troll DW Canopy User Manual 

 

Page 5                                                                                                         Atair Canopies

 

 

 

 

 

In memory of Dwain Weston. Jan 31

st

 1973 - October 5

th

 2003 

 

Dwain Weston, changed the face of modern BASE jumping. He took the sport to a 
new level, leaving it much richer than when he found it. Dwain is remembered for his 
incredible aerial skills but his contribution, achievements and passion for BASE jumping 

will live on in all of us.  

 

 

Photo by: Yuri 

 

Dwain was the first to spot the potential of the original prototype Troll canopy during 

the Petronas tower event in Malaysia, he approached Atair and asked to try the 
canopy. Dwain performed many jumps with the canopy from various objects and 
provided Atair with invaluable input on how to improve the canopy.  
 
Dwain spent much time with Stane, the owner of Atair, discussing the optimum 

characteristics of BASE canopies and the desired features he would like to see in future 
canopies. These discussions were instrumental in the design of the Troll DW canopy.

  

 

 

Содержание Troll DW


























Отзывы: