Atair Canopies Troll DW Скачать руководство пользователя страница 14 | Manualshive

Страница: 14 / 25

Atair Canopies Troll DW Скачать руководство пользователя страница 14

wwwAtairCanopies.com

Troll DW Canopy User Manual

Page 14 Atair Canopies

Do the same on the other side, leaving the center cell to hang down in the middle.
Gently place the canopy on the ground, keeping tension on the lines. The neater you

place the canopy, the easier it will be to redress it once it’s on the ground. Find the
three nose cells on each side and tease them out gently. They should be resting neatly
on top of one another, resembling figure 1b above.

Figure 2

Figure 2: Pick a side to start redressing. From the bottom stabiliser, reach in between
the A and B lines and flake all of the fabric to the outside, keeping the lines orderly in
the center. From the next stabilizer, reach between the B and C lines, flaking all of the
fabric to the outside, keeping the lines orderly in the center. Now reach in between

the C and D lines, flaking all of the fabric to the outside, keeping the lines orderly in the

center.

Be certain to maintain tension on the lines by gently pulling the appropriate fabric
from the top of the canopy during this process. Next, be sure to clear the fabric
between the D lines and the control lines. This is done by placing your hand between
the D lines and the control lines and pulling away from the container. This will remove
the slack in the fabric between these two points. Repeat all of this on the other side
and redress by lifting the tail up so that the lines are exposed. From either side, you can
ensure that the fabric is all pulled away from the container and that the stabilizers are

clear of the lines as well. During this process, be sure to keep tension on the lines.
Ensure that the pack job is symmetrical by looking at the line attachment points on
each side and making certain they are even.

«
...
12
13
14
15
16
...
»

Содержание Troll DW


























Отзывы:

Нет отзывов