background image

iv

Notices

Federal.Communications.Commission.Statement

This device complies with Part 15 of the FCC Rules. Operation is subject to the 

following two conditions:
•  This device may not cause harmful interference, and
•  This device must accept any interference received including interference that 

may cause undesired operation.

This equipment has been tested and found to comply with the limits for a 

Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are 

designed to provide reasonable protection against harmful interference in a 

residential installation. This equipment generates, uses and can radiate radio 

frequency energy and, if not installed and used in accordance with manufacturer’s 

instructions, may cause harmful interference to radio communications. However, 

there is no guarantee that interference will not occur in a particular installation. If 

this equipment does cause harmful interference to radio or television reception, 

which can be determined by turning the equipment off and on, the user is 

encouraged to try to correct the interference by one or more of the following 

measures:
•  Reorient or relocate the receiving antenna.
•  Increase the separation between the equipment and receiver.
•  Connect the equipment to an outlet on a circuit different from that to which the 

receiver is connected.

•  Consult the dealer or an experienced radio/TV technician for help.

The use of shielded cables for connection of the monitor to the graphics card is 

required to assure compliance with FCC regulations. Changes or modifications 

to this unit not expressly approved by the party responsible for compliance 
could void the user’s authority to operate this equipment.

As an Energy Star

® 

Partner, our company has determined that this 

product meets the Energy Star

® 

guidelines for energy efficiency.

Canadian.Department.of.Communications.Statement

This digital apparatus does not exceed the Class B limits for radio noise emissions 

from digital apparatus set out in the Radio Interference Regulations of the 

Canadian Department of Communications.
This class B digital apparatus complies with Canadian ICES-003.
This Class B digital apparatus meets all requirements of the Canadian Interference 

- Causing Equipment Regulations.
Cet appareil numérique de la classe B respecte toutes les exigences du Réglement 

sur le matériel brouiller du Canada.

Содержание SP1920 series


























Отзывы: