background image

PV100A Series

39

Care during use

• 

Do not walk on the power cord or allow anything to rest on it.

• 

Do not spill water or any other liquids on your system.

• 

When the system is turned off, a small amount of electrical current still 

flows. Always unplug the power cord from the power outlets before 

cleaning the system.

• 

Please use this product with care when operating this product at full 

load, as the product may reach temperatures of up to 60˚C and the 

outer casing may reach temperatures of up to 72˚C

• 

If you encounter the following technical problems with the product, 

unplug the power cord and contact a qualified service technician or 

your retailer.

 

– 

The power cord or plug is damaged.

 

– 

Liquid has been spilled into the system.

 

– 

The system does not function properly even if you follow  

 

the operating instructions.

 

– 

The system was dropped or the cabinet is damaged.

 

– 

The system performance changes.

NO DISASSEMBLY

The warranty does not apply to the products 

that have been disassembled by users

Lithium-Ion Battery Warning

CAUTION

: Danger of explosion if battery is incorrectly replaced. 

Replace only with the same or equivalent type recommended 

by the manufacturer. Dispose of used batteries according to the 

manufacturer’s instructions.

Содержание PV100A Series





















































Отзывы: