background image

vii

Notices

Federal Communications Commission Statement

This device complies with Part 15 of the FCC Rules. Operation is subject to 

the following two conditions:
•  This device may not cause harmful interference, and
•  This device must accept any interference received including 

interference that may cause undesired operation.

This equipment has been tested and found to comply with the limits for a 

Class B digital device, pursuant to Part 15 of the FCC Rules. These limits 

are designed to provide reasonable protection against harmful interference 

in a residential installation. This equipment generates, uses and can radiate 

radio frequency energy and, if not installed and used in accordance with 

manufacturerʼs instructions, may cause harmful interference to radio 

communications. However, there is no guarantee that interference will 

not occur in a particular installation. If this equipment does cause harmful 

interference to radio or television reception, which can be determined by 

turning the equipment off and on, the user is encouraged to try to correct 

the interference by one or more of the following measures:
•  Reorient or relocate the receiving antenna.
•  Increase the separation between the equipment and receiver.
•  Connect the equipment to an outlet on a circuit different from that to 

which the receiver is connected.

•  Consult the dealer or an experienced radio/TV technician for help.

Canadian Department of Communications Statement

This digital apparatus does not exceed the Class B limits for radio noise 

emissions from digital apparatus set out in the Radio Interference 

Regulations of the Canadian Department of Communications.
This class B digital apparatus complies with Canadian  

ICES-003.

The use of shielded cables for connection of the monitor to the graphics 

card is required to assure compliance with FCC regulations. Changes 

or modifications to this unit not expressly approved by the party 

responsible for compliance could void the userʼs authority to operate 

this equipment.

Содержание P5MT-MX C





























































































































































Отзывы: