Asus P2Z-B Скачать руководство пользователя страница 49 | Manualshive

Страница: 49 / 96

background image

ASUS P2Z-B User’s Manual

49

IV. BIOS SETUP

IV

. BIOS SETUP

Chipset Features

16-bit I/O Recovery Time (1 BUSCLK) / 8-bit I/O Recovery Time (1 BUSCLK)
Timing for 16-bit and 8-bit ISA cards, respectively. Leave on default setting.

Graphics Aperture Size (64MB)
Memory-mapped, graphics data structures can reside in a Graphics Aperture. Leave
on default setting.

Video Memory Cache Mode (UC)
USWC (uncacheable, speculative write combining) is a new cache technology for
the video memory of the processor. It can greatly improve the display speed by
caching the display data. You must leave this on the default setting of UC
(uncacheable) if your display card cannot support this feature, otherwise your sys-
tem may not boot.

PCI 2.1 Support (Enabled)
This function allows you to enable or disable PCI 2.1 features including passive release
and delayed transaction. Leave Enabled (default setting) for PCI 2.1 compliancy.

Memory Hole At 15M–16M (Disabled)
Enabling this feature reserves 15MB to 16MB memory address space to ISA expan-
sion cards that specifically require this setting. This makes the memory from 15MB
and up unavailable to the system. Expansion cards can only access memory up to
16MB. The default is Disabled.

....................................................................................................................................
Onboard FDC Controller (Enabled)
When Enabled, this field allows you to connect your floppy disk drives to the onboard
floppy disk drive connector instead of a separate controller card. If you want to use a
different controller card to connect the floppy disk drives, set this field to Disabled.

Onboard FDC Swap A & B (No Swap)
This field allows you to reverse the hardware drive letter assignments of your floppy
disk drives. Two options are available: No Swap and Swap AB. If you want to switch
drive letter assignments through the onboard chipset, set this field to Swap AB.

Onboard Serial Port 1 (3F8H/IRQ4)
Settings are 3F8H/IRQ4, 2F8H/IRQ3, 3E8H/IRQ4, 2E8H/IRQ10, and Disabled for
the onboard serial connector.

Onboard Serial Port 2 (2F8H/IRQ3)
Settings are 3F8H/IRQ4, 2F8H/IRQ3, 3E8H/IRQ4, 2E8H/IRQ10, and Disabled for
the onboard serial connector.

«
...
47
48
49
50
51
...
»

Содержание P2Z-B

































































































Отзывы:

Нет отзывов

Похожие инструкции для P2Z-B

Virtex-II Pro ML300

Бренд: Xilinx Страницы: 17

Бренд: Biostar Страницы: 53

Бренд: Safran Страницы: 26

Бренд: Biostar Страницы: 27

970 Extreme3 R2.0

Бренд: ASROCK Страницы: 70

Бренд: Texas Instruments Страницы: 25

Бренд: Atmel Страницы: 23

MBD-J-JNC9VL-H81

Бренд: JETWAY Страницы: 43

Бренд: Norco Страницы: 78

Бренд: NXP Semiconductors Страницы: 12

Бренд: DFI Страницы: 5

Бренд: Gigabyte Страницы: 100

Бренд: Biostar Страницы: 63

Бренд: Renesas Страницы: 30

Бренд: Parker Страницы: 56

VVDI Mini Key Tool

Бренд: Xhorse Страницы: 17

Бренд: Erreka Страницы: 4

MT9V113PACSTCH-GEVB

Бренд: ON Semiconductor Страницы: 5

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды