manualshive.com logo in svg

Asus P2V-B, Руководство пользователя

Поделиться
Скачать
Asus P2V-B Скачать руководство пользователя страница 56

ASUS P2V-B User’s Manual

56

IV.  BIOS SETUP

Load Defaults

IV

.  BIOS SETUP

Load BIOS Defaults

The “Load BIOS Defaults” option allows you to load the troubleshooting default
values permanently stored in the BIOS ROM.  These default settings are non-opti-
mal and disable all high performance features.  To load these default settings, high-
light “Load BIOS Defaults” on the main screen and then press <Enter>.  The system
displays a confirmation message on the screen.  Press <Y> and then <Enter> to
confirm.  Press <N> and then <Enter> to abort.  This feature does not affect the
fields on the Standard CMOS Setup screen.

Load Setup Defaults

The “Load Setup Defaults” option allows you to load the default values to the sys-
tem configuration fields.  These default values are the optimized configuration set-
tings for the system.  To load these default values, highlight “Load Setup Defaults”
on the main screen and then press <Enter>.  The system displays a confirmation
message on the screen.  Press <Y> and then <Enter> to confirm.  Press <N> and
then <Enter> to abort.  This feature does not affect the fields on the Standard CMOS
Setup screen.

Содержание P2V-B

































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды