manualshive.com logo in svg

Asus P2V-B, Руководство пользователя

Поделиться
Скачать
Asus P2V-B Скачать руководство пользователя страница 34

34

ASUS P2V-B User’s Manual

III. HARDWARE SETUP

Connectors

III.  H/W SETUP

18. Wake-On-Ring Connector (2-pin WOR)

This connector connects to internal modem cards with a Wake-On-Ring output.
The connector powers up the system when a ringup packet or signal is received
through the internal modem card. NOTE: For external modems, Wake-On-Ring
is detected through the COM port.

IMPORTANT: This feature requires that PWR UP On Modem Act Power Up Con-
trol is set to Enabled (see Power Management Setup under BIOS SETUP) and that your
system has an ATX power supply with at least 720mA +5V standby power.

P2V-B Wake-On-Ring Connector

WOR

Pin 2 PIXRI#
Pin 1 Ground

R

P2V-B

19. Chassis Intrusion Sensor Lead (4-1 pin CHASIS)

This lead is for a chassis intrusion monitor or sensor. The sensor is triggered
when a high level signal is sent to the “chassis signal” lead. This occurs when a
panel switch or light detector is triggered. This function requires the optional
ASUS CIDB Chassis Intrusion Photo Sensor Module (see APPENDIX) to be
installed.

P2V-B Chassis Intrusion Sensor Lead

+5V

olt P

o

wer Supply Standb

y

Ground

Chassis Signal

R

P2V-B

Содержание P2V-B

































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды