Asus CUWE Скачать руководство пользователя страница 35 | Manualshive

Страница: 35 / 136

background image

ASUS CUWE User’s Manual

35

3. HARDWARE SETUP

Connectors

3. H/W SETUP

12) Wake-On-LAN Connector (3-pin WOL_CON)

This connector connects to a LAN card with a Wake-On-LAN output, such as
the ASUS PCI-L101 Ethernet card (not required for onboard LAN model). The
connector powers up the system when a wakeup packet or signal is received
through the LAN card.

IMPORTANT: This feature requires that Wake On LAN is set to Enabled (see
4.5.1 Power Up Control) and that your system has an ATX power supply with at
least 720mA +5V standby power.

01

01

01

®

CUWE

CUWE Wake-On-LAN Connector

IMPORTANT: Requires an ATX power
supply with at least 720mA +5 volt
standby power

+5 Volt Standby

PME

Ground

WOL_CON

13) Wake-On-Ring Connector (2-pin WOR)

This connector connects to internal modem cards with a Wake-On-Ring output.
The connector powers up the system when a ringup packet or signal is received
through the internal modem card. NOTE: For external modems, Wake-On-Ring
is detected through the COM port.

IMPORTANT:

This feature requires that PWR Up On Modem Act is set to

Enabled (see 4.5.1 Power Up Control) and that your system has an ATX power
supply with at least 720mA +5V standby power.

CUWE Wake-On-Ring Connector

WOR

RI#

Ground

2

1

01

01

01

®

CUWE

«
...
33
34
35
36
37
...
»

Содержание CUWE









































































































































Отзывы:

Нет отзывов

Похожие инструкции для CUWE

Бренд: SurfLink Страницы: 9

Бренд: ASROCK Страницы: 126

Бренд: J&W Страницы: 40

Бренд: FAAC Страницы: 8

Бренд: Texas Instruments Страницы: 38

Бренд: JS Automation Страницы: 18

Бренд: ECS Страницы: 64

Бренд: BCM Страницы: 93

Бренд: Gigabyte Страницы: 37

Бренд: MSI Страницы: 85

SAM9N12/CN11-EK

Бренд: Atmel Страницы: 69

Бренд: Micrel Страницы: 10

Бренд: Embedian Страницы: 70

Бренд: MSI Страницы: 126

Бренд: ASROCK Страницы: 38

Бренд: TRIGEM Страницы: 17

Бренд: Fujitsu Страницы: 22

Бренд: Fujitsu Страницы: 23

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды