Asus CUWE Скачать руководство пользователя страница 34 | Manualshive

Страница: 34 / 136

background image

34

ASUS CUWE User’s Manual

Connectors

3. H/W SETUP

3. HARDWARE SETUP

10) Primary / Secondary IDE Connectors (40-1 pin PRIMARY/SECONDARY)

These connectors support the provided IDE hard disk ribbon cable.
After connecting the single end to the board, connect the two plugs at the other
end to your hard disk(s). If you install two hard disks, you must configure the
second drive to Slave mode by setting its jumper accordingly. Please refer to
your hard disk documentation for the jumper settings. BIOS now supports spe-
cific device bootup (see Boot Sequence in 4.6 Boot Menu).

(Pin 20 is removed

to prevent inserting in the wrong orientation when using ribbon cables with
pin 20 plugged).

TIP: You may configure two hard disks to be both Masters with two ribbon
cables – one for the primary IDE connector and another for the secondary IDE
connector. You may install one operating system on an IDE drive and another on
a SCSI drive and select the boot disk through Boot Sequence in 4.6 Boot Menu.
IMPORTANT: UltraDMA/66 IDE devices must use an 80-conductor IDE
cable.

01

01

01

®

CUWE

CUWE IDE Connectors

NOTE: Orient the red markings
(usually zigzag) on the IDE
ribbon cable to

PIN 1

Primary IDE Connector

Secondary IDE Connector

PIN 1

11) Floppy Disk Drive Connector (34-1 pin FLOPPY)

This connector supports the provided floppy drive ribbon cable. After connect-
ing the single end to the board, connect the two plugs on the other end to the
floppy drives. (Pin 5 is removed to prevent inserting in the wrong orienta-
tion when using ribbon cables with pin 5 plugged).

NOTE: Orient the red markings on
the floppy ribbon cable to

PIN 1

CUWE Floppy Disk Drive Connector

PIN 1

01

01

01

®

CUWE

«
...
32
33
34
35
36
...
»

Содержание CUWE









































































































































Отзывы:

Нет отзывов

Похожие инструкции для CUWE

Бренд: Datavan Страницы: 15

Бренд: Abit Страницы: 72

Бренд: J&W Страницы: 40

PCM-8152 3rd Generation

Бренд: Aaeon Страницы: 6

conga-HPC/EVAL-Server

Бренд: Congatec Страницы: 54

Бренд: Zetex Страницы: 8

Бренд: IEI Technology Страницы: 131

Бренд: DFI Страницы: 62

C5535 DSPShield

Бренд: Texas Instruments Страницы: 49

Бренд: Gigabyte Страницы: 96

Бренд: Microchip Technology Страницы: 2

Бренд: IBASE Technology Страницы: 62

Бренд: Gigabyte Страницы: 46

Бренд: Texas Instruments Страницы: 33

Бренд: Aaeon Страницы: 78

Бренд: Zamel Страницы: 3

Бренд: J&W Страницы: 36

Бренд: Microchip Technology Страницы: 18

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды