Asus Aaeon BOXER-6641 Скачать руководство пользователя страница 6

Страница: 6 / 134

Preface

Fan

les

s E

mb
ed

ded

BO
XE

R-

Safety Precautions

Please read the following safety instructions carefully. It is advised that you keep this

manual for future references

All cautions and warnings on the device should be noted.

Make sure the power source matches the power rating of the device.

Position the power cord so that people cannot step on it. Do not place anything

over the power cord.

Always completely disconnect the power before working on the system

’

hardware.

No connections should be made when the system is powered as a sudden rush

of power may damage sensitive electronic components.

If the device is not to be used for a long time, disconnect it from the power

supply to avoid damage by transient over-voltage.

Always disconnect this device from any power supply before cleaning.

While cleaning, use a damp cloth instead of liquid or spray detergents.

Make sure the device is installed near a power outlet and is easily accessible.

10.

Keep this device away from humidity.

11.

Place the device on a solid surface during installation to prevent falls.

12.

Do not cover the openings on the device to ensure optimal heat dissipation.

13.

Watch out for high temperatures when the system is running.

14.

Do not touch the heat sink or heat spreader when the system is running

15.

Never pour any liquid into the openings. This could cause fire or electric shock.

16.

As most electronic components are sensitive to static electrical charge, be sure

to ground yourself to prevent static charge when installing the internal

components. Use a grounding wrist strap and contain all electronic components

in any static-shielded containers.

Содержание Aaeon BOXER-6641







































































































































Результаты поиска

Содержание Aaeon BOXER-6641

Отзывы:

Похожие инструкции для Aaeon BOXER-6641

Бренды по названию

Популярные бренды

Asus Aaeon BOXER-6641, Руководство пользователя

Результаты поиска

Содержание Aaeon BOXER-6641

Отзывы:

Похожие инструкции для Aaeon BOXER-6641

Бренды по названию

Популярные бренды