ASTRO AMC-2000 Скачать руководство пользователя страница 6 | Manualshive

Страница: 6 / 18

background image

Page 4

Figure 3

WARNING: FAILURE TO DO THIS RESULTS IN SERIOUS DAMAGE TO
ENVELOPE FEEDER AND DUPLCATOR.

14.

Move Paper Stack Height Adjustment to low position.

15.

Turn Duplicator Hand Wheel so suction feet are in uppermost position. Remove two outer
suction feet from Duplicator.

WARNING: FAILURE TO DO SO MAY DAMAGE OUTER SUCTION FEED AND
PREVENT PROPER OPERATION OF DUPLICATOR.

Figure 4

«
...
4
5
6
7
8
...
»

Содержание AMC-2000



















Отзывы:

Нет отзывов

Похожие инструкции для AMC-2000

Бренд: Tanco Страницы: 72

Бренд: HABYS Страницы: 16

Бренд: Acterna Страницы: 72

Бренд: Keithley Страницы: 36

Бренд: Rain-Flo Irrigation Страницы: 16

Бренд: Landoll Страницы: 6

Бренд: ParaBody Страницы: 9

Бренд: ParaBody Страницы: 3

Бренд: MacDon Страницы: 45

Бренд: H&S Страницы: 30

Бренд: JB-Lighting Страницы: 60

Бренд: Raymarine Страницы: 90

Бренд: JB-Lighting Страницы: 60

Бренд: Farmet Страницы: 102

Бренд: Gardner Bender Страницы: 8

Бренд: NARIKA Страницы: 2

Бренд: Tascam Страницы: 8

Бренд: Nemalux Страницы: 6

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды