manualshive.com logo in svg

Astria Zeta21ZMN F1241, Инструкция по установке и эксплуатации

Поделиться
Скачать
Astria Zeta21ZMN F1241 Скачать руководство пользователя страница 13

Astria.US.com

126885-01B

13

Figure 16 - Equipment Shutoff Valve

Open

Closed

Equipment 

Shutoff Valve

Figure 17 - Checking Gas Joints (Propane/LP Only)

Propane/LP 

Supply Tank

Equipment 

Shutoff Valve

Gas Valve

Figure 18 - Checking Gas Joints (Natural Gas Only)

Equipment 

Shutoff Valve

Gas 

Meter

Gas Regulator or 

Gas Control Valve

INSTALLATION  

Continued

PRESSURE TESTING FIREPLACE GAS CONNECTIONS

1.  Open equipment shutoff valve (see Figure 16).
2.  Open main gas valve located on or near gas meter for natural gas 

or open propane/LP supply tank valve.

3.  Make sure control knob of fireplace is in the OFF position.
4.  Check all joints from equipment shutoff valve to gas control valve 

(Remote-Ready Models) (see Figures 17 or 18). Apply noncor-

rosive leak detection fluid to all joints. Bubbles forming show a 

leak.

5.  Correct all leaks at once.
6.  Light fireplace (see Operating Fireplace, page 15). Check all other 

internal joints for leaks.

7.  Turn off fireplace (see To Turn Off Gas to Appliance, page 16).

OPTIONAL WALL MOUNTED THERMOSTAT - GWMT1 

(Remote-Ready Models Only)

 WARNING: Read and follow installation instruc-

tions. Installation should be done by a qualified 

installer familiar with low-voltage wiring procedures.

 WARNING: Do not connect this thermostat to any 

electrical source! Electrical shock and/or fire hazard 

will occur.

1.  Disconnect jumper wire from control valve (see Figure 19, page 

14).

2.  Connect one terminal of 25 ft. wire to “TPTH” terminal on control 

valve (see Figure 19, page 14).

3.  Connect remaining wire terminal to the “TH” terminal on the control 

valve. Make sure that wire terminals are in the positions on your 

unit as pictured in Figure 19.

4.  Route the 25 ft. wire to a convenient location to mount your ther-

mostat (no outside wall). 

IMPORTANT:

 The wire may be shortened 

but must not be lengthened.

  The thermostat should be mounted 54" above the floor in a loca-

tion where there is good air circulation. Avoid heat sources such 

as lamps, direct sunlight, fireplace or heat and air conditioning 

ducts.

5.  Gently remove the cover of the thermostat from the base. Grasp 

the sides of the cover firmly and pull to separate from the base.

6.  Feed the electrical wires through the rectangular slots on each side 

of the base (see Figure 20, page 14).

 WARNING: Do not connect the thermostat to a power 

source. Electrical shock and/or a fire hazard will occur.

7.  Connect one bare wire end to each terminal (“W” and “R”) of the 

thermostat base (see Figure 21, page 14).

8.  Install the base onto the wall with the provided screws.
9.  Move the temperature adjustment back and forth to insure the 

bimetal is free from restrictions.

Содержание Zeta21ZMN F1241





























Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды