Astria.us.com
126780-01D
16
OPERATION
Figure 27 - Control Knob, Igniter Button and Remote Selector
Switch
Selector
Switch
Control
Knob in OFF
Position
Flame Adjustment
Knob
Igniter
NOTE: The burner may light if hand-held remote was on when selector
switch was last turned off. You can now turn burner on and off with
hand-held remote control unit.
IMPORTANT: Do not leave selector switch in the REMOTE or ON
position when pilot is not lit. This will drain the battery.
FOR YOUR SAFETY
READ BEFORE LIGHTING
WARNING: If you do not follow these instructions
exactly, a fire or explosion may result causing property
damage, personal injury or loss of life.
NOTICE: You must light the pilot before using the hand-
held remote control unit. See Lighting Instructions.
A. This appliance has a pilot which must be lighted with a piezo
igniter. When lightning the pilot, follow these instructions
exactly.
B. BEFORE LIGHTING smell all around the appliance area for gas.
Be sure to smell next to the floor because some gas is heavier
than air and will settle on the floor.
WHAT TO DO IF YOU SMELL GAS
• Do not try to light any appliance.
• Do not touch any electric switch; do not use any phone in your
building.
• Immediately call your gas supplier from a neighbor’s phone.
Follow the gas supplier’s instructions.
• If you cannot reach your gas supplier, call the fire department.
C. Use only your hand to push in or turn gas control knob. Never
use tools. If the knob will not push in or turn by hand, do not
try to repair it, call a qualified technician. Force or attempted
repair may result in a fire.
D. Do not use this appliance if any part has been under water. Imme-
diately call a qualified service technician to inspect the appliance
and to replace any part of the control system and any gas control
which has been under water.
LIGHTING
INSTRUCTIONS
1. STOP! Read the safety information, above.
2. Make sure switch is in the OFF position.
3. Be sure gas line shut-off valve is OPEN.
4. Press in and turn control knob clockwise
to the OFF
position (see Figure 27).
NOTE: Knob cannot be turned from PILOT to OFF unless knob is
pushed in slightly. DO NOT FORCE.
5. Wait five (5) minutes to clear out any gas. If you then smell gas,
STOP! Follow "B" in the safety information in column 1. If you
don't smell gas, go on the next step.
6. Press in and turn control knob counterclockwise
to the
PILOT position. Press in control knob for five (5) seconds (see
Figure 27).
7. With control knob pressed in, press and release igniter button.
This will light pilot. If needed, keep pressing igniter button until
pilot lights.
NOTE: If pilot does not stay lit, contact a qualified service person
or gas supplier for repairs.
8. Keep control knob pressed in for 30 seconds after lighting pilot.
After 30 seconds, release control knob.
• If control knob does not pop out when released, turn off gas
supply and contact a qualified service person or gas supplier
for repairs.
NOTE: If pilot goes out, repeat steps 4 through 8.
TO TURN OFF GAS
TO APPLIANCE
MANUAL LIGHTING
PROCEDURE
OPTIONAL HAND-HELD
REMOTE OPERATION
9. Slightly push in and turn control knob counterclockwise
to
the ON position.
10.Wait one minute and move switch to the ON position to light
burner.
NOTE: AUTO is only functional when using optional remote control
accessory.
11. Set flame adjustment knob to any level between HI and LO.
1. Turn control knob clockwise
to the OFF position.
2a. Set switch in the OFF position.
2b. If Using Optional Hand-Held Remote: Set selector switch in the
OFF position to prevent draining battery.
3. Close equipment shutoff valve (see Figure 13, Page 10).
1. Follow steps 1 through 6 under Lighting Instructions.
2. Press control knob and light pilot with match.
3. Keep control knob pressed in for 30 seconds after lighting pilot.
After 30 seconds, release control knob. Now follow steps 9
through 11, under Lighting Instructions.
NOTE: All remote control accessories must be purchased separately
(see Accessories, Page 24). Follow instructions included with the
remote control.
After lighting, let pilot flame burn for about one minute. Turn control
knob to ON position. Adjust flame adjustment knob anywhere between
HI and LO. Slide the selector switch to the REMOTE position (see
Figure 27).
Solid fuels shall not be burned in this appliance.