ASTEC RT130 Скачать руководство пользователя страница 26

Страница: 26 / 64

OPERATING INSTRUCTIONS

AU106984 G7B

Cupped Teeth

RT160001

Cupped teeth are the best in cutting light to medium soil.

The cupped design of the tooth cuts the soil and then

moves the soil up and out of the trench.

NOTE:

Additional digging teeth combinations may be

available to meet particular soil conditions. See your Astec

dealer for additional information.

BEFORE YOU OPERATE

Starting the Trench

NOTE:

Know the location of all underground utilities

before starting.

1. Make sure all persons are away from the machine

before you start the engine and while you are

trenching.

2. To assist in digging a straight trench, stretch a string

line along the trench route on the side opposite the

auger discharge.

3. Engage the operator presence control.
4. After the engine has reached operating temperature,

move the machine so the trencher boom is several

feet beyond the starting point of the trench.

5. Align the machine to the center line of the new

trench.

6. Lower the trencher boom close to the ground.
7. Move the throttle to the MAX position.
8. Engage the digging chain. Slowly lower the trencher

boom into the ground to the necessary depth.

NOTE:

The operator presence control levers must be

continually engaged or the digging chain will stop.

9. When the trencher boom is completely down to the

necessary depth, move the direction/speed control

slowly.

10. Use the direction/speed control to adjust the machine

speed for the soil conditions.

NOTE:

If the drive wheels start to slip excessively,

decrease the speed.

11. When the trenching is complete, move the direction/

speed control to NEUTRAL, and slowly raise the

trencher boom.

12. Move the digging chain control to the stop position
13. Move the throttle to the MIN position and stop the

engine.

WARNING:

Be careful when working near the

side of a trench. Serious injury or death can result

if the walls of the trench fall.

WARNING:

Make sure all people are clear of the

digging chain while the digging chain is rotating.

Serious injury or death can result from contact

with the digging chain.

WARNING:

Sharp moving parts - do not remove

restraint bar. Keep clear of hazardous area. KEEP

CLEAR. Serious injury or death can result from

bodily contact.

WARNING:

Never allow anyone in the trench

while digging.

Содержание RT130

































































Результаты поиска

Содержание RT130

Отзывы:

Бренды по названию

Популярные бренды

ASTEC RT130, Руководство оператора

Результаты поиска

Содержание RT130

Отзывы:

Бренды по названию

Популярные бренды