Associated 12-1015 rev-B Скачать руководство пользователя страница 21

Страница: 21 / 50

___________________________________________________________________________________

‐

12‐1015 rev‐B

User’s Manual Version 14.12

11. Press

key and the display will show: (Fig.28) below:

12. Referring to the Table list (Fig.27) basing on 80D26L, check the battery

type: WET, MF, Sealed MF or Closed MF (CMF) as each category has
different CCA ratings. For instance, if the battery is a Sealed MF (CMF)
then it is rated at 630 CCA.

Note: WET

- Wet

Cell

Type

- Maintenance

Free

Type

SMF - Closed

Sealed

Maintenance

Free

13. To enter the value 630, press key will increase the original value of 100

(Fig.29) by step of 100 units to 600. Likewise use key to increase the
last two digits (00) to 30 by step of 5 units for each pressing. (See Fig. 29)

Once the CCA rating of the battery is confirmed, press

key will start

the testing process. Refer to the display below (Fig. 30).

Figure 28

Fig. 29

Input Battery Rating

Increase/decrease:



Single digit





By hundredth



500

CCA

[Enter] to proceed.

Input Battery Rating

Increase/decrease:



Single digit





By hundredths



630

CCA

[Enter] to proceed.

Содержание 12-1015 rev-B



















































Результаты поиска

Содержание 12-1015 rev-B

Отзывы:

Похожие инструкции для 12-1015 rev-B

Бренды по названию

Популярные бренды

Associated 12-1015 rev-B, Руководство пользователя

Результаты поиска

Содержание 12-1015 rev-B

Отзывы:

Похожие инструкции для 12-1015 rev-B

Бренды по названию

Популярные бренды