manualshive.com logo in svg

Associated Electrics RC8.2e, Руководство пользователя

Поделиться
Скачать
Associated Electrics RC8.2e Скачать руководство пользователя страница 27

27

:: Radio Tray Assembly - Bag K

:: Radio Tray Assembly (cont.) - Bag K

:: Radio Tray Assembly (cont.) - Bag K

89208

3x14mm 

fhcs

89504

Radio 

tray 

(bottom)

x4

89006

Servo 

spacers

89229

Countersunk 

washers

(blue)

89506

Hook and 

loop battery 

straps

89505

RC8e 

battery 

tray

x3

x4

x4

Servo mounts vary per 

servo manufacturer.  

Space your servos low 

to the chassis without 

touching the bottom.

Note:  speed control 

not included.  

Attatch with servo 

tape #6727.

Note:  hook and loop 

straps are removed 

for view clarity.

Note:  hook and loop 

straps are removed 

for view clarity.

Note:  route the 

speed control 

receiver wire 

through this 

opening.

Note:  route the 

speed control 

receiver wire 

through this 

opening.

!

!

!

!

!

!

!

89509

Flywheel 

opening 

cover

89507

Battery 

tray pads

Bottom

View

!

Note:  servo 

not included.

!

Содержание RC8.2e



















































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды