manualshive.com logo in svg

Associated Electrics RC8.2e, Руководство пользователя

Поделиться
Скачать
Associated Electrics RC8.2e Скачать руководство пользователя страница 12

12

:: Front Suspension Assembly (cont.) - Bag E & EE

:: Front Suspension Assembly (cont.) - Bag E & EE

:: Front Suspension Assembly (cont.) - Bag E & EE

89317

Droop

screw

25192

3x20mm

shcs

89537

RC8.2 

swaybar 

ball joint

89207

4x12mm

bhcs

89558

RC8.2 

caster 

blocks

89029

Steering 

block 

bushing

(short)

89029

Steering block 

bushing (long)

89536

RC8.2 

swaybar 

pivot ball

89537

RC8.2  

swaybar

drop link

89550

RC8.2 

front 

arms

89032

16 deg. caster 

angle bushing

(blue)

89032

16 deg. caster 

angle bushing

(red)

89206

4x10mm

bhcs

Do not tighten until 

bushing is keyed 

into steering block.

Note:

One drop only.

Spread evenly 

inside the threads.

Note:

Key bushings into 

steering block.

!

!

!

#1596

thread lock

#1596

thread lock

#1596

thread lock

Build right 

and left 

sides!

Build right 

and left 

sides!

Droop 

screw 

placement!

Build right 

and left 

sides!

Build Two!

!

!

!

!

!

!

!

Note: direction

blue

red

16 deg

1 6 deg

31520

2.5x6mm

bhcs

89041

Outer 

hinge pin

Содержание RC8.2e



















































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды