background image

12

-

 BATTERY

 +

+

 BATTERY

 -

BATTERY

 +

step 5

ELECTRICAL INSTALLATION

Solder your single cell batteries together 
with  battery braid or battery bars. Solder 
plus (+) to minus (-).
Strap the batteries to the chassis with 
strapping tape.
Attach your speed control and receiver 
where shown with the #6726 servo tape.
Insert the #4510 roll over antenna into 
the antenna mount, wrap the antenna 
wire up the antenna, and secure the wire 
with the antenna cap.
Now connect the electronic speed control 
and steering servo to your receiver 

according to your radio or ESC 
instructions,

 then connect the motor 

and batteries to the ESC.

ELECTRICAL ITEMS ARE NOT INCLUDED IN KIT

4

5

BAG E

REMOVE THESE 
PARTS FOR:

TEAM: steps 5-6

TOOLS USED

7337, qty 2
washer

1:1

6515, qty 2
3mm x 10mm
gold

1:1

4510, qty 1
roll over antenna

4510, qty 1
antenna cap

strapping tape

6726, qty 1
servo tape strip

PINION GEAR INSTALLATION

Slide the pinion gear purchased 
separately onto the shaft so that the 
gear is 1/16" away from the motor 
can and tighten the set screw to 
hold it in place.

MOTOR INSTALLATION

Insert the motor, the pinion gear 
coming through the right side motor 
bulkhead.
Tighten the motor to the bulkhead 
with two #6515 screws and two 
#7337 gold washers.
Set the gear mesh so that there is 
very little play between the spur 
and pinion gear.

1

2

3

2

3

receiver

speed
control

4

REMOVE THESE 
PARTS FOR:

TEAM: steps 3-4

step 4

FRONT BODY MOUNTS

Place the #4508 chassis protector on the 
front chassis tip, and slide the #9269 
screw up from the bottom as shown into 
the #4535 front body mount. 
Add one #6332 body clip to the post 
according to your body height. Put your 
painted body on, add the #7320 body 
washer to the mount over the body, and 
top off with the other #6332 clip.

4508

9269

4535

7320

6332

6332

assembled

1:1

1:1

1:1

TOOLS USED

6332, qty 4
body clip

9269, qty 2
5-40 x 1/2

7320, qty 2
large body washer

4535, qty 2
front body mount

4508, qty 2
chassis protector

Содержание RC12 L3

















Отзывы: