Copyright © 1997, 2014 Yale Security Inc., an ASSA ABLOY Group company. All rights reserved.
Reproduction in whole or in part without the express written permission of Yale Security Inc. is prohibited.
80-9377-0551-020 (05-14)
ASSA ABLOY
3
• Track Assembly
Remove slider assembly parts from box
# 40-7940-0050-000 and insert into channel in the
order shown. See illustration on page 2 or 4.
Use of a hold open device
or assembly will void the
UL® listing for this product.
Insert end caps into ends of track prior to installing.
•
Install track to frame.
Place the assembled
slide track against frame with the open side down,
stop and cushion blocks toward the hinge. Move
the slider to the opposite end of the slide track.
Secure slide track with 1/4-20 flat head phillips
drive mounting screws.
•
Connect arm to track.
Open door approximately
5"(127mm), rotate arm to slider and place end on
stud. Push down on arm and tap gently to seat
(to prevent stud from turning during assembly).
Secure with 1/4-20 x 5/8" long truss (rounded)
head phillips drive screw with thread lock.
CAUTION: Closer arm is under spring tension and
may be difficult to rotate.
•
Set door stop angle.
Open door to the angle
you want the door to stop. With the door held at that
location, slide stop with cushion block against slider.
Tighten the stop position screw (large set screw)
with 3/16" hex wrench (from screw pack) until secure.
Release door.
•
Adjust closer
(see page 5) before installing cover.
•
Install Cover.
Slide insert into cover slot
(see
illustration). Fasten cover to closer with (2)
8-32 x 1/4" long round head phillips drive screws.
Installation Sequence
Pull or Push Side Mount
•
Determine hand of door and type of installation
from
illustrations on page 1.
•
Use template dimensions
to locate fastener holes on door and
frame. See "Preparation for Fasteners" chart below.
Frame:
Prepare the frame for mounting track. Drill and tap holes
for 1/4-20 machine screws or #14 wood screws.
Door:
Prepare the door for mounting closer. Drill and tap (4)
holes for 1/4-20 machine screws, #14 wood screws,
3/8 diameter sex-nuts, or through bolts and grommet-nuts.
Note:
If drop plate is used, prepare holes for 7786 drop plate
instead of closer. Secure drop plate before mounting closer.
•
Fasten closer to door or drop plate.
Position spring tube away
from hinge. See arm indexing illustrations (above right) for valve
positioning (up or down). Secure mounting screws.
• Assemble Slide Arm.
Insert flat arm rod into arm tube with the
counterbore screw hole facing up. Align counterbore with the 3rd
hole in the arm tube and secure with 8-32 x 1/4 long hex socket
cap screw. See illustration on page 2 or 4.
•
Install arm on closer pinion
see arm indexing illustrations
(above right). Position slide arm with counterbore facing up
and align with pinion flat as illustrated. Install onto pinion. Secure
with washer and flat head phillips drive arm screw with thread lock.
Arm in position
Left hand
Right hand
Pinion Flat
Arm Indexing
Valves down
Valves up
PULL MOUNT
Arm in position
(Bottom View)
Right hand
Pinion Flat
Arm Indexing
Left hand
Valves down
Valves up
PUSH MOUNT
(Top View)
Aluminum or
Wood
Preparation for Fasteners
Fasteners Door or Frame Drill Sizes
#14 type "A"
S.M. screw Wood
7/32" (5.56mm)
Arm: 1-1/4" (32mm)
Closer: 2-3/4" (70mm)
1/4" -20 machine Metal
drill: #7 (.201")
screw
tap: 1/4" -20
Sex-nuts and bolts Hollow Metal 9/32" (7.00mm) through
3/8" (9.50mm) door-face
opposite to closer
3/8" (9.50mm) through
Through-bolts and
9/32" (7.00mm) through;
grommet-nuts All
3/8" (9.50mm) dia. x
3/8" (10mm) deep door-
face opposite to closer
(Optional)
