Assa Abloy ADAMS RITE PS-SE Скачать руководство пользователя страница 9

Страница: 9 / 16

80-0180-339, Rev 2

2. REMOVE the orange jumper block installed into the BATT BACKUP

connector of the PS-SE circuit board by pulling the orange jumper
free from the circuit board.

NOTE:

Mounting points are available in the PS-SE enclosure for the

Battery Backup System circuit board.

3. INSTALL the Battery Backup System circuit board in the enclosure

(see Figure 4, “Location of Battery Backup System”).

Figure 4. Location of the Battery Backup System

NOTE:

The Adams Rite Battery Backup System circuit board has a

short wiring harness to connect to the PS-SE circuit board.

4. CONNECT the orange connector of the wiring harness into the BATT

BACKUP connector of the PS-SE circuit board.

5. WIRE the battery terminals of one battery to the (+) and (

–) terminals

on the BATT1 connector of the PS-SE circuit board.

6. WIRE the battery terminals of second battery to the (+) and (

–)

terminals on the BATT.21 connector of the PS-SE circuit board.

Содержание ADAMS RITE PS-SE

















Результаты поиска

Содержание ADAMS RITE PS-SE

Отзывы:

Похожие инструкции для ADAMS RITE PS-SE

Бренды по названию

Популярные бренды

Assa Abloy ADAMS RITE PS-SE, Руководство пользователя и инструкции по установке

Результаты поиска

Содержание ADAMS RITE PS-SE

Отзывы:

Похожие инструкции для ADAMS RITE PS-SE

Бренды по названию

Популярные бренды