ASM AllPro APB2525H Скачать руководство пользователя страница 8

Страница: 8 / 24

309882

4. Trigger gun until a constant stream of water sprays from tip indicating air is purged from the system.

5. Be sure spark plug ignition cable is pushed firmly onto spark plug.

6. Move throttle to Rabbit (fast) position and choke to CHOKE

position.

Do not allow pressure washer to idle more than 10

minutes. This causes circulating water to overheat and
serious damage to the pump. The pump is equipped
with a thermal valve to help prevent severe damage if
circulating water is overheating.

Turn off pressure washer if it will not be spraying at

least every 10 minutes or if thermal valve activates. If
heated inlet water is used, reduce this time.

Do not operate pressure washer with inlet water

screen removed. This screen helps keep abrasive
sediment which could clog pump or damage cylinders,
out of pump.

Do not pump caustic materials.

CAUTION

7. Pull the starter rope quickly to start the engine. Pull and return the

rope until the engine starts. HINT: Placing one foot on the pres-
sure washer as a brace provides better leverage.

NOTE:

For easier starting, have one person start pressure washer while another triggers gun.

ti3237a

ti3240a

ti3242a

Содержание AllPro APB2525H

























Результаты поиска

Содержание AllPro APB2525H

Отзывы:

Похожие инструкции для AllPro APB2525H

Бренды по названию

Популярные бренды

ASM AllPro APB2525H, Руководство по эксплуатации

Результаты поиска

Содержание AllPro APB2525H

Отзывы:

Похожие инструкции для AllPro APB2525H

Бренды по названию

Популярные бренды