ASM AllPro APB2525H Скачать руководство пользователя страница 7 | Manualshive

Страница: 7 / 24

background image

7

309882

1. Check oil level of engine.

Startup
Always use this startup procedure to ensure that the pressure washer is started
safely and properly.

Always engage gun trigger safety latch when you stop spraying. This reduces the risk of fluid injection or
splashing in eyes or on skin if gun is bumped or accidentally triggered.

Always observe the CAUTIONS in this section to avoid costly damage to pressure washer.

If you use the Sandblaster Kit, see Sandblaster Kit Manual for detailed cleaning information.

.

Operation

2. Check fuel level.

3. Turn on water supply.

Never run pressure washer without wa-
ter. Costly pump damage will result.
Always be sure water supply is complete-
ly turned on before you run pressure
washer.

CAUTION

«
...
5
6
7
8
9
...
»

Содержание AllPro APB2525H

























Отзывы:

Нет отзывов

Похожие инструкции для AllPro APB2525H

Martha Stewart MTS-1450PW

Бренд: SNOWJOE Страницы: 16

Бренд: GoWISE USA Страницы: 26

Бренд: Hoover Страницы: 37

Бренд: NEFF Страницы: 48

Auto-Washer 1100 AC170

Бренд: Hoover Страницы: 10

Бренд: PowerBoss Страницы: 36

Бренд: Hisense Страницы: 14

Бренд: Farberware Страницы: 40

Бренд: sangiorgio Страницы: 129

Бренд: Kärcher Страницы: 112

Бренд: Bella Страницы: 19

Бренд: Kärcher Страницы: 54

Бренд: Samsung Страницы: 110

WW80H5440E Series

Бренд: Samsung Страницы: 88

Бренд: Samsung Страницы: 136

WW80H5400E Series

Бренд: Samsung Страницы: 88

Бренд: Electrolux Страницы: 2

Бренд: Electrolux Страницы: 2

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды