You can vary the temperature as shown below:
150 °F (65 °C) / 160 °F (70 °C)
Sanitation:
124 °F (51 °C) / 150 °F (65 °C)
Normal:
140 °F (60 °C)/150 °F (65 °C)
Heavy:
85 °F (30 °C) / 140 °F (60 °C)
Quick:
105 °F (40 °C) / 120 °F (50 °C)
Delicate:
130 °F (55 °C) / 140 °F (60 °C)
Eco:
130 °F (55 °C) / 150 °F (65 °C)
Upper half:
130 °F (55 °C) / 150 °F (65 °C)
Lower half:
Long dry
Activate Long dry to increase final rinse temperature and dry time
to improve drying results. This causes a slight increase in energy
consumption. This option can be used with all programs except
Rinse & Hold.
If you want a program with Short dry, press again so that the field
under the button turns off.
Delayed start
When you select Delayed start, the dishwasher will start 1-24
hours after you press the Start/Stop button.
1 Press the button once to activate Delayed start. Press the
button several times – or hold it in – to set the desired number
of hours.
2 Press Start/Stop and the dishwasher counts down 1 hour at
a time and starts after the selected delay.
Press and hold Start/Stop for three seconds if you want to cancel
the Delayed start option.
NOTE!
Remember to press the Start/Stop button to start the program.
Start the dishwasher
Press and hold Start/Stop until the display shows
(the door
open symbol). This indicates that the dishwasher is ready to start.
Close the door properly and immediately, otherwise the dishwash-
er will not start. The display flashes three times with the remaining
time to indicate that the program has started.
NOTE!
Close the door within four seconds, otherwise the dishwasher
will not start.
Time remaining
Once you have selected a program and options, the display indi-
cates how long the program took the last time it was used. Once
you have started the dishwasher, the display indicates how much
program time remains. The remaining time is updated after the
water for the final rinse has been heated.
This may differ somewhat from time to time depending on the
temperature of the water supply, the amount of dishes, the ambi-
ent temperature, and other factors.
While the program is running, the time counts down and the re-
maining program time is shown on the display. The remaining
time is shown, for example, as 1:15, which means the program
will run for another 1 hour and 15 minutes.
NOTE!
During the first run of each program, the remaining time dis-
played can be slightly misleading, as the dishwasher is estimat-
ing the time. When you run the program a second time, the
dishwasher will calculate the remaining time based on the
previous duration of the program.
Stopping or changing a program
If you want to change program after starting the dishwasher,
open the door then press and hold Start/Stop for three seconds.
Add more detergent if the lid of the detergent dispenser has
opened. Then choose a new program, press Start/Stop, and close
the door immediately.
WARNING!
The dishwasher door must not be open while a program is in
progress. If the door is open, "000" is shown on the display.
Press any button then press and hold Start/Stop for three sec-
onds if you want to cancel a program.
If the dishwasher is turned off using
the On/Left-on mode button or due
to a power failure
If the dishwashing program is not finished, this is indicated by a
buzzer and "000" appearing on the display when power is restored
to the machine. Press any button and close the door immediately
for the dishwashing program to continue.
NOTE!
During drying, the program is interrupted if the power is cut or
the door is open for more than 2 minutes.
Once the program has finished
Once the program has finished, "End" appears on the display.
At the end of the program, one short signal will sound. Chapter
Settings describes how to change this function.
Once the cycle is complete, the dishwasher uses standby power
only. Shut off the water supply valve after every use.
9
