ASG X-PAQ ASG-NW2500 Скачать руководство пользователя

Страница: 14 / 37

Serial Printer

This menu determines the baud rate of the serial
printer, and if the ASG-NW2500 makes ACOP
communications over serial, the baud rate of those
communications. The available selections are 9600,
19200, 38400, 57600, and 115200 baud rates.

See section later in this document for output format and example.

Note: When the serial printer is set to “OFF”, the ACOP connections will operate at 9600 baud.

Serial Print Format

This menu determines the format of the data sent out
through the serial printer port. Options are ‘None’,
‘Line’, and ‘CSV’.

See section later in this document for output format
examples.

Note: When the serial printer format is set to “None”, no data will be transmitted from the
RS-232 port.

Bar Code Reader

This menu determines the baud rate of the serial bar
code reader. The available selections are 9600,
19200, 38400, 57600, and 115200 baud rate.

Edit Password

This menu allows you to change the password
required to enter Setup Mode.

Be sure to remember

the password entered or you will not be able to
configure the device through the HMI.

Pick Task

This menu allows you to select a task. You may
also select tasks with a bar code (11) or ACOP (MID
0018) command.

Note: See the section “Mapping of ACOP commands
to X-PAQ

Inputs” later in this document for X-PAQ

setup requirements to execute this

function.

Содержание X-PAQ ASG-NW2500






































Результаты поиска

Содержание X-PAQ ASG-NW2500

Отзывы:

Похожие инструкции для X-PAQ ASG-NW2500

Бренды по названию

Популярные бренды

ASG X-PAQ ASG-NW2500, Руководство пользователя

Результаты поиска

Содержание X-PAQ ASG-NW2500

Отзывы:

Похожие инструкции для X-PAQ ASG-NW2500

Бренды по названию

Популярные бренды