manualshive.com logo in svg

Aseptico ADU-40CF Command Air, Руководство по эксплуатации, техническому обслуживанию и ремонту, Страница: 12 / 16

Поделиться
Скачать
Aseptico ADU-40CF Command Air Скачать руководство пользователя страница 12

Replacing the level sensors

Tools:

8 in. crescent wrench 

1. Trace the electrical leads from the tank level sensor and the tilt

shutoff  sensor  to  the  control  board  and  remove  the  sensors'

connectors. Note the wiring configuration from the sensors to

their connectors. Note the mating connector located on board.

2. Note the orientation, then unscrew the level sensor from the

tank. Remove the mounting hardware from the tilt sensor.

3. Install the new sensors as required. On the tank sensor, make

sure  the  peaked  portion  of  the  exposed  fitting  labeled  N.O.

(normally open) is positioned upward. Rewire and attach the

new electrical connector at the original board location.

Replacing the electric intake pump 

(Figure Q)

Tools: 

Pliers, 5/16 deep well socket or driver, and

a flat blade screwdriver

1. Remove the snapper type clamp from each end

of  the  pump  by  pushing  its  tabs  in  opposite

directions.  Use  pliers  to  improve  clamp

manipulation. Work the tubing off each end of

the pump.

2. Loosen the green retaining screw and remove

the grounding wire from the pump.

3. Remove the two nuts which mount the pump to

the bracket.

4. Trace and disconnect the pump wiring from the

control board and the solenoid valve. Connect

the new wires at the old locations.

5. Replace the pump and reassemble by reversing steps. Make sure that the flow direction arrow on

the new pump points away from the solenoid valve.

Replacing the electronics board 

(Figure R)

Tools: 

1/4  open  face  wrench  or  crescent  wrench,  Phillips

screwdriver, and pliers

1.  Remove  the  board  mounting  hardware  from  each  of  the  four

corners of the control board.

2. Wire the new board by tracing the leads from the old board or by

following the wiring schematic,  

Refer to Figure S.

3. Secure the new control board in each corner with the mounting

hardware.

Page 12

Figure Q  - Intake Pump

Figure R - Electronics Board

Figure P  - Level Sensors

Tilt Shutoff Sensor

Tank

Level Sensor

Содержание ADU-40CF Command Air

















Отзывы:

Нет отзывов