ASCOM T942PX Скачать руководство пользователя страница 16

TD 90227GB

2006-09-18/ Ver. C

System Installation
On Site Paging System

14

For several reasons an address register should be kept for each installation, with the name, 
address, and location of each unit.

Address Register

0 0

0 1

0 2

0 3

0 4

T942C

T940PX

T840IU

T966CI

U952T

Attic, head office

Exchange room, head office

Exchange room, head office

Reception, head office

Beneath the roof,  storeroom

Address (hex)

Unit

Location

Figure 14. Example of an address register.

When using sequential transmission, the sequence number is set by sections 5-8 of the 
address switch. The central transmitter always transmits in sequence 0 (address 00) and 
the transmitters that are meant to transmit simultaneously should also have hex 0 as the 
first digit in the address. Next sequence uses hex 1 as the first address digit and so on. 
Each sequence can have up to 16 transmitters. Sequential transmission is used to avoid 
interference between the transmitters but cannot be used in speech systems.

Address Register

0 0

0 1

0 2

0 3

0 4

1 0

2 0

T942C

T942PX

T840IU

T966CI

U952T

U952T

U952T

Attic, head office

Exchange room, head office

Exchange room, head office

Reception, head office

Beneath the roof,  storeroom

Cellar, head office

Culvert, head office

Address (hex)

Unit

Location

Figure 15. Example of an address register in an installation with sequential 

transmission.

9

System Check

After the system installation, a functional check is made according to the installation guide 
for each unit.

Initiate a paging and check that the pocket receiver responds correctly. Repeat this for 
every unit that can generate pagings including pocket transceivers. In speech systems 
make sure that the voice messages are clear. Check all other functions such as absent 
indication, busy tone, mobile-to-mobile calls etc.

Note: 

The battery saving time (set in the PUP or PDM depending on handset) must be set 

to a battery saving time of 0.5, 2 or 5 seconds. The mode 0 seconds is for handset test 
purpose only and is not supported by the system. Keeping the mode 0 seconds during 

Содержание T942PX



















Отзывы: