background image

© 2020 ASCO Power Technologies. All Rights Reserved

2

IO-75016

01/2020

For access to self-service tools and chat support visit se.com/us/en/work/support  or call 1-888-778-2733 for technical assistance

ASCO Model 146 (Edco PLP-S Series)

Surge Protective Device (SPD) 

 
 

 

 

Safety Information 

 

  Important Information

 

   

Read these instructions carefully and look at the equipment to become 

familiar with the device before trying to install, operate, service or maintain it. 

The following special messages may appear throughout this bulletin or on the 

equipment to warn of potential hazards or to call attention to information that 

clarifies or simplifies a procedure. 

 

   

The addition of either symbol to a “Danger” or “Warning” safety label 

indicates that an electrical hazard exists which will result in personal 

injury if the instructions are not followed. 

 

   

This is the safety alert symbol. It is used to alert you to potential 

personal injury hazards. Obey all safety messages that follow this 

symbol to avoid possible injury or death. 

 

 

 

DANGER

 

DANGER

 indicates a hazardous situation which, if not avoided,  

will result in

 death or serious injury. 

 

 

WARNING

 

WARNING

 indicates a hazardous situation which, if not avoided,  

could result in

 death or serious injury. 

 

 

CAUTION

 

CAUTION

 indicates a hazardous situation which, if not avoided,  

could result in

 minor or moderate injury. 

 

NOTICE

NOTICE is used to address practices not related to physical injury. The safety 

alert symbol shall not be used with this signal word. 

 

 

 

 

  Please Note 

 

   

Electrical equipment should be installed, operated, serviced, and maintained only 

by qualified personnel. No responsibility is assumed by ASCO Power Technologies 

for any consequences arising out of the use of this material. 

A qualified person is one who has skills and knowledge related to the 

construction, installation, and operation of electrical equipment and has received 

safety training to recognize and avoid the hazards involved. 

 

 

Содержание 146









Отзывы: