ASCO POWER TECHNOLOGIES 450 Скачать руководство пользователя

Страница: 6 / 24

For troubleshooting, call technical assistance at 1-800-237-4567 or [email protected]

IO-70075

08/2020

ASCO 450/451/452/453 Surge Protective Device (SPD)

Introduction

HAZARD OF ELECTRIC SHOCK, EXPLOSION, OR ARC FLASH

• Apply appropriate personal protective equipment (PPE) and follow safe

electrical work practices. See NFPA 70E, NOM-029-STPS or CSA Z462.

•

This equipment must only be installed and serviced by qualified

electrical personnel.

•

Turn off all power supplying this equipment before working on or inside

equipment.

•

Always use a properly rated voltage sensing device to confirm power is

off.

• Replace all devices, doors and covers before turning on power to this

equipment.

•

This equipment must be effectively grounded per all applicable codes.

Use an equipment-grounding conductor to connect this equipment to the

power system ground.

Failure to follow these instructions will result in death or serious injury.

Proper installation is imperative to maximize the ASCO 450/451/452/453

surge protective device’s effectiveness and performance. Read the entire

instruction bulletin before beginning the installation. These instructions

are not intended to replace national or local electrical codes. Check all

applicable electrical codes to verify compliance. Installation of modular surge

suppressors should only be performed by qualified electrical personnel.

Inspect the entire shipping container for damage or signs of mishandling

before unpacking the device. Remove the packing material and further

inspect the device for any obvious shipping damage. If any damage is found

and is a result of shipping or handling, immediately file a claim with the

shipping company.

The device should be stored in a clean, dry environment. Storage

temperature is -40°F (-40°C) to +140°F (+60°C). All of the packaging

materials should be left intact until the device is ready for installation.

English, Spanish, and French versions of all safety labels (Danger, Warning,

and Caution) are provided.

DANGER

Introduction

Unpacking and Preliminary

Inspection

Storage

Safety Labels

Surge Protective Device

(SPD) Location

Considerations

Environment

Audible Noise

Mounting

Note:

For troubleshooting, call technical

assistance at 1-800-237-4567 or

[email protected]

The device is designed to operate in an ambient temperature range of

-25° C (-13° F) to +60° C (140° F) with a relative humidity of 0 to 95% non-

condensing.

The device background noise is negligible and does not restrict the location

of the installation.

This device is designed to be installed as component assemblies intended

for installation within electrical equipment. See page 15 for mounting

dimensions and weight

Содержание 450























Результаты поиска

Содержание 450

Отзывы:

Похожие инструкции для 450

Бренды по названию

Популярные бренды

ASCO POWER TECHNOLOGIES 450, Руководство по установке и эксплуатации

Результаты поиска

Содержание 450

Отзывы:

Похожие инструкции для 450

Бренды по названию

Популярные бренды