Art SGX LT Скачать руководство пользователя страница 11 | Manualshive

Страница: 11 / 30

Art SGX LT Скачать руководство пользователя страница 11

PREAMP CONTROLS/DIRT CHANNEL

DIRT DRIVE

To adjust the input drive of the dirt channel use the Dirt Drive control. The

control range of input drive is 0 to 11. When set at zero, no signal is allowed

to enter the dirt circuits so you will have no output. A little bit above zero

will provide a warm overdrive sound. As you increase the control, distortion

drive increases. At eleven, maximum signal and crunch is achieved. Set this

control to get the right amount of overdrive or distortion in the dirt channel.

THRUST

Thrust is the bass frequency cut and boost filter control. A (+)12 dB boost in

gain and a (-)12dB cut in gain are the maximum ranges. At zero, (12 o'clock) the

filter is flat. the center frequency (the actual filter frequency) is 180 HZ.

MID VOICING

To control your midrange tone use the Mid Voicing control. A (+)12 dB boost in

gain and a (-)12dB cut in gain are the maximum ranges. At zero, (12 o'clock) the

filter is flat. the center frequency (the actual filter frequency) is 850Hz.

EDGE

High end frequencies are controlled with the Edge control. A (+)12 dB boost in

gain and a (-)12dB cut in gain are the maximum ranges. At zero, (12 o'clock) the

filter is flat. the center frequency (the actual filter frequency) is 4.00Khz.

DISTORTION LEVEL

The Distortion Level control sets the final level of the Dirt Channel. Set this

control so your Signal LED is lit while you're playing and the Clip LED lights

with sharp attacks. Be careful not to set this control to high because you might

clip the digital effects. Monitor the digital section by moving the Mix slider

fully to the right and listen to the output. After you have set your input gain,

set your Mix control.

TELLTALES

OVERDRIVE ACTIVE INDICATOR

When this LED is on, it indicates the Dirt channel is active.

SEVEN SEGMENT DISPLAY

The Seven Segment Display keeps you constantly informed of your Preset or MIDI

program number. Preset numbers are displayed from 01 to 99 and then, for presets

over 99 a letter and number. Refer to the preset list at rear of this manual for

preset "numbers". Bypass is indicated by two horizontal bars.

INPUT LEVEL INDICATORS

Front panel LED indicators show the status of the input signal level as it enters

the digital processor. The Signal LED indicates the presense of audio signal. If

the CLIP LED is lit, it indicates you are clipping the digital processor. For

7

«
...
9
10
11
12
13
...
»

Содержание SGX LT































Отзывы:

Нет отзывов