Arrow Storage Products PC1010 Скачать руководство пользователя страница 1

Страница: 1 / 24

* Size rounded off to the nearest foot

CAUTION: SOME PARTS HAVE SHARP EDGES. CARE

MUST BE TAKEN WHEN HANDLING THE VARIOUS PIECES

TO AVOID A MISHAP. FOR SAFETY SAKE, PLEASE READ

SAFETY INFORMATION PROVIDED IN THIS MANUAL

BEFORE BEGINNING CONSTRUCTION. WEAR GLOVES

WHEN HANDLING METAL PARTS.

705220511

Owner's Manual & Assembly Instructions

Storage Area: 99 Sq. Ft. 848 Cu. Ft.

9,2 m

24,0 m

Missing Parts, Questions on Assembly?

Call: 1-800-851-1085 or assist@arrow-

sheds.com

Do not return to dealer, they are not

equipped to handle your requests.

PATIO COVER/CARPORT

Model No. PC1010 PC1010EU

Attached

Exterior Dimensions Interior Dimensions

* Approx. Foundation

(Roof Edge to Roof Edge)

(Wall toFacia)

Size Size

Width Depth Height Width Depth Height

10' x 10' 123" x 130 1/4"

120 3/4" 121 1/2" 106 1/2" 119" 119 1/4" 102"

3,0 m x 3,0 m 312,4 cm x 330,8 cm 306,7 cm 308,6 cm 270,5 cm 302,3 cm 302,9 cm 259,1 cm

BUILDING DIMENSIONS

DC01

Содержание PC1010

























Результаты поиска

Содержание PC1010

Отзывы:

Похожие инструкции для PC1010

Бренды по названию

Популярные бренды

Arrow Storage Products PC1010, Руководство пользователя и инструкции по сборке

Результаты поиска

Содержание PC1010

Отзывы:

Похожие инструкции для PC1010

Бренды по названию

Популярные бренды