16
Problem
Possible cause and solution
The appliance does not ignite immediately.
•
Ensure that the gas valves are open.
•
Check if sparks are produced when igniting the appliance.
•
Push the control knob(s) for 5 seconds before you attempt to ignite the appliance.
•
Ensure that the burner(s) is / are clean.
•
Check if the gas cylinder(s) is / are not empty.
The appliance does not ignite at all.
•
The electrode maybe covered with cooking residues. Use a clean swab and alcohol to clean.
•
The electrode or wire may be damaged. Replace with a new electrode assembly with wire.
•
The wires of the electrode are loose or fall off. Replace with a new electrode assembly with wire.
•
Clear the orifi ce if blocked.
•
The electrode does not aim at burner hole. Align the electrode and the burner hole. Adjust the
distance between metal pin of the electrode and burner hole to 3 - 5 mm.
No spark noise.
•
The electrode does not aim at burner hole. Align the electrode and the burner hole. Adjust the
distance between metal pin of the electrode and burner hole to 3 - 5 mm.
Pressure regulator makes noise.
•
Check if the ventilation opening on the pressure regulator is plugged. Unplug the opening and
wait 5 minutes before starting again.
•
Check if the ventilation openings are covered up. Check the appearance of the fl ames and
remove possible plugging.
The appliance only heats up from 100 °C to 150 °C;
low heat with knob(s) in
position.
•
Check to make sure that the thermometer functions properly. To do this, lay an oven
thermometer in the appliance and compare the temperature with that of the temperature setting
on the appliance itself.
•
Check all gas connections for gas leaks. If there is a gas leak, tighten the connection.
•
Straighten up the gas hose(s) if bent or kinked
•
Clear the burner(s) or the orifi ce if blocked.
•
Have your gas dealer check the gas cylinder(s), in case of low gas pressure.
•
Gas supply is not suffi cient as there is not enough gas in the gas cylinder(s). Refi ll or replace
the gas cylinder(s).
The appliance takes a long time to heat up.
•
The appliance takes longer to heat up when it is cold outside. The time required to heat from
250 °C to 320 °C is usually about 10 - 15 minutes.
•
Gas supply is not suffi cient as there is not enough gas in the gas cylinder(s). Refi ll or replace
the gas cylinder(s).
•
Check if the gas hose(s) is / are blocked or clogged.
The burner fl ame is not blue.
•
Check if there is too much or too little air being supplied.
•
Check if the burner is misaligned.
•
In case of incomplete combustion contact specialist.
Burner cannot be ignited by match.
•
Open the valve of the gas cylinder(s) and / or the pressure regulator(s), if no gas is being fed to
the burner(s).
•
Clear the tubes of the burner(s) if the gas fl ow is not smooth.
•
Re-assemble burner(s) and valve(s) if you deem the assembly to be incorrect.
• WARNING!
Turn all the control knobs to the off positions
, if any burner does not ignite within
5 seconds
. Wait for
5 minutes
to let the gas dissipate and try again.
Flare-up.
•
Excessive fat content in the meat, remove part of the fat before grilling.
•
Reduce the temperature.
•
Clean if you spot deposits of grease.
Flame raised from the burner.
•
Excessive gas pressure, contact your gas dealer.
CLEANING, MAINTENANCE AND REPAIR
WARNING!
Always switch the appliance off and let it cool down before performing inspection, maintenance and cleaning work!
Do not immerse burner(s) into water or other liquids. If they become wet, let them dry thoroughly and check the function afterwards.
Cleaning
1. Clean the appliance after each use with a slightly damp cloth and a little soap. Use a brush for hard to reach places.
2. Remove stubborn dirt with high pressure air (max. 3 bar).
NOTE:
Do not use chemical, alkaline, abrasive or other aggressive detergents or disinfectants to clean this appliance as they might be harmful to its
surfaces.
Stainless steel surfaces
1. Wipe all stainless steel surfaces with a wet soft cloth. Use a mild detergent to remove grease.
2. Remove grease and food remains from the fi re box with a plastic or wooden spatula.
3. Remove the burner(s), before cleaning the fi re box.
Grease tray(s)
1. Avoid that the grease tray(s) overfl ow(s). Empty regularly during use.
2. Clean the grease tray(s) after each use using warm water and a mild detergent.
NOTE:
Add sand or cat litter to the grease tray(s) before use to avoid that the grease sticks on the surface.
MAINTENANCE
Before and after each use, check the appliance or accessories or attachments for wear and damage. If required, exchange them for new ones as described in
this instruction manual. Observe the technical requirements (
→
TECHNICAL DATA).
GB
(IM)3A-001327-0002_SRGG31403A_Multi_V2_200904.indb 16
(IM)3A-001327-0002_SRGG31403A_Multi_V2_200904.indb 16
07/09/2020 19:17
07/09/2020 19:17
