Arnica VIRA, Инструкция по эксплуатации

Страница: 9 / 28

WARNING : Never use the appliance to clean up flammable or explosive
solvents, object soaked with such solvents, explosive dusts, liquids such as
petrol, oil, alcohol, thinners and objects that are hotter than 60oC, as this
will cause a serious explosion and fire hazard! The appliance must not be
used near
flammable substances and must not be used to clean up health endangering
dust.
II. GENERAL DESCRIPTION
Main parts of the appliance are shown as follows (Figure 1)
A. MOTOR UNIT
This group contains motor, pump, switch and operating units on. Top of this group,
there is a FILTER which filters dust and other particles from blowing air. If you
remove the foam filter, you will see a large plastic float in a case. As the
container fills, this plastic float rises up and cuts off the vacuum action to warn
you when the container needs emptying.
A1 - Pump switch
A2 - On/Off switch
A3 - Shampoo hose connector
A4
– Air outlet filter housing
A5 - Air outlet filter
A6 - Air outlet filter cover
A7 - Float group
A8 - Foam filter
B. CONTAINER GROUP
Container Group is the middle part of the cleaner for collecting dust and dirty
water. This group is fastened with Motor Unit using clip locks. Shampoo reservoir
which contains shampoo and clean water is placed under the container group.
B1 - Container
B2 - Water filter body
B3 - Sponge for water filter
B4 - Water filter tube
B5 - Black seal
B6 - Clamps
B7 - Locking nest
B8 - Suction inlet
C. SHAMPOO RESERVOIR GROUP
Shampoo reservoir contains shampoo and clean water.
When pump is oper-
ated, shampoo and water is extracted from the shampoo reservoir. Coming water
from tank through water tube is sprayed. Shampoo reservoir is located between
container and wheel group.
C1 - Shampoo reservoir
C2 - Short shampoo hose
C3 - Shampoo hose connection adapter
C4 - Water level indicator
D. WHEEL GROUP
D1 - Wheel chassis
D2 - Wheel
D3 - Locking peg
E. HOSE GROUP
This group contains suction hose with hand grip, shampoo hose group and suction
tubes. Suction hose is connected to container group by inserting the suction hose
into the suction inlet. Suction tubes are connected to hand grip if necessary.
Handgrip contains a mechanical sliding for regulating suction power and shampoo
trigger for spraying the water and shampoo. Hose group can be placed onto the
motor unit by the help of hanger.
E1 - Suction hose fixing part
E2 - Shampoo hose fixing part
E3 - Shampoo hose
E4 - Clips
E5 - Suction hose
E6 - Shampoo trigger
E7 - Suction power control
E8 - Handgrip
E9 - Suction tube
E10 - Tube hook
F. SHAMPOO NOZZLE
It is used for sucking liquids on the carpets, mats, floors. Water and shampoo
is sprayed through this accessory. For floors it is used with hard floor adapter
attachment.
F1 - Shampoo nozzle
F2 - Hard floor adapter
G. MINI WETSWEEP
This nozzle is very suitable for shampooing furniture, curtains and sucking liquids
on the narrow surfaces.
H. ACCESSORIES GROUP
There are various accessories for different cleaning purposes
H1 - Accessories Holder
H2 - Crevice Nozzle
H3 - Round Nozzle
H4 - Upholstery Nozzle
H5 - Nozzle
H6 - Perfume
H7 - Shampoo
III. TECHNICAL FEATURES
Voltage : 230V~, 50 Hz
Power (Max.) : 2400W Max.
Electric Insulation Class II
Degree of Protection : IPX4
Container Capacity : 10 lt.
Cord Length : 6 m.
Used Life : 10 Year
IV. PREPARING FOR USE
• ATTENTION – Do not insert the mains plug into the wall socket until the
appliance is completely ready for use
• Detach the shampoo hose between shampoo reservoir and back side of Motor
Unit by pulling carefully.
• Lift up the Motor Unit using the handle provided, take the attachments out
of the container.
• When unpacking, please check that all parts are included and undamaged.
• Keep the accessories for further uses
• Make sure that foam filter is fixed on the float case.
• Put the motor unit back onto the appliance and close the clamps.
•To connect the hose, insert it into the hose connector.
V. OPERATING THE APPLIANCE
DRY VACUUMING
• Always be sure that the mains plug is removed from the wall socket.
• Make sure that the container, tubes and hose group are dry and clean.
• Unlock the clamps and lift the motor unit upside down.
• Do not use the appliance without the foam filter.
• Lift up the motor unit
• Remove the water filter body and fill container with clean water (Max. 2 lt).
Replace water filter body.
•Put the motor unit back onto appliance and lock the clamps.
• Fit the cleaning accessories most suited to the type of operation to be
performed, on to the suction tubes or directly in to the handgrip.
• For effective cleaning the following accessory can be used.
» Nozzle (H5) for removing dust from carpets, mats and hard floor surfaces.
» Crevice nozzle (H2) for cleaning narrow corners and hard to reach places
» Directly suction tube (E9) for sucking soil, shavings, crumbs, fluff.
» Upholstery Nozzle (H4) and the suction tube for removing dust from shelves,
books, lamp shades, frames, ornaments, curtains, clothes, electronic equip-
ment’s, surfaces.
• Pull the mains cord out of the appliance and insert the mains plug into the
wall socket. Push the On/Off Button (A2) to switch the appliance on.
ATTENTION : Do not operate the pump
SHAMPOOING AND WET VACUUMING
• Lift the motor unit from the container.
•Make sure that the foam filter is inserted. (Figure 5)
• Remove water filter tube. It may cause extremely bubbling.
• Replace water filter body (Figure 12)
NEVER FILL THE CONTAINER WITH CLEAN WATER WHILE PREPARING APPLI-
ANCE FOR SHAMPOOING
•Fill the shampoo resarvoir with clean water (use C4 water level indicator as
reference) and shampoo (dose is mentioned on shampoo bottle) Place the
shampoo reservoir onto the wheel group (Figure 15)
• Place the container onto the shampoo reservoir and the motor unit onto the
container. Lock the clamps. (Figure 4)
9