OPERATION AND PAIRING
The Armacost Lighting wireless-ready dimmer (Model DIM2IN1-
RF-WR) will need to be programmed or paired to recognize the
radio frequency signal of the wireless touchpad.
1. Following the instructions
that were supplied with
your wireless ready dimmer,
connect dimmer to power
supply and your LED lighting.
Ensure the dimmer and LED
lights operate properly. Have
the wireless touchpad in close
range to the receiver, 10 feet
or closer for pairing.
2. Disconnect power to the
dimmer by unplugging or
switching off the power
supply. Leave off for at least
5 seconds. You can also
disconnect power by pulling
out the green block connector
on the dimmer.
3. To pair, press and hold the brightness up and brightness
down keys simultaneously. While continuing to hold the
buttons, restore power to the power supply and dimmer.
To test, press the on/off key of the wireless touchpad to confirm
that it can control the receiver. If not, repeat the process.
Depending on the lighting
layout, and to reduce the
need for extra wiring, it can
be advantageous to have
one touchpad control or be
“paired” to multiple rotary
knob dimmer receivers
(wireless ready models only).
To add or pair more
receivers, repeat the same
process with additional
receivers. The wireless
touchpad will pass its
unique code to multiple
receivers.
To synchronize multiple
receivers, so that all lights
turn on/off and dim in
unison to one touchpad,
simply manually turn off
all receivers with each
rotary knob. Then press the
power on key of the wireless
touchpad. All lights should
turn on at the same time.
Note: you can also “un-pair” the dimmers by following the process
above, but press the power on and brightness up keys instead.
IMPORTANT: Do not press any key on the wireless touchpad
repeatedly or too quickly or the receivers can lose synchronization or
fail to operate in unison. Firm, deliberate button presses are required
to keep multiple dimmers in synch. For effective synchronization,
all receivers must be within range of the single wireless touchpad.
In the event of a power outage, once power is restored to the
LED lighting, the brightness will be at the level where the rotary
knob on the receiver unit was last set, not the last setting on the
wireless touchpad. This is also true if the lights are switched off
by turning off the power supply.
The Wireless Touchpad will operate properly while the rotary
knob of the 2-in-1 Dimmer is in any position, but it is
recommended that it be set to fully off. This will prevent your
lighting from turning on without input following a power outage.
TROUBLESHOOTING
The wireless touchpad does not work.
Be sure the wireless touchpad is in range of the receiver. Try
moving the touchpad closer to the receiver. The dimmer is
a radio frequency (RF) device and, as such, the range of the
wireless remote control is dependent on many factors. Actual
operational distance will vary based on walls and line of sight
obstructions, and other nearby electronic devices.
Be sure the battery has a charge. Replace the battery if in doubt
(Alkaline 23A 12-volt). A battery will last from 6 months up to 3
years, depending on usage.
The receiver may need to be paired again with your transmitter.
If the dimmer receiver is functioning properly, and the touchpad
battery is fresh, yet the touchpad will not control the lighting,
repeat the pairing instructions.
If you would like to purchase additional dimmer transmitters
or receivers, visit the retailer where you made your purchase
or visit armacostlighting.com.
SPECIFICATIONS
Wireless working frequency ..................................... 433.92Mhz
Transmitter battery .................................... Alkaline 23A 12-volt
FCC ID ............................................................ NWKHF10008
Country of origin .............................................................China
Limited 1-year warranty. This product is for dry location
use only. Improper installation, improper powering, abuse,
or failure to use this device for its intended purpose will
void warranty. Proof of purchase is required for all returns.
Questions? Email [email protected].
This item is a Radio Frequency Device (RF), and as such the
range of the remote control is dependent on many factors. Actual
operational distance will vary based on walls and line of sight
obstructions, and other nearby electronic devices.
This device complies with Part 15 of the FCC Rules. Operation
is subject to the following two conditions: (1) this device may
not cause harmful interference, and (2) this device must accept
any interference received, including interference that may cause
undesired operation. Changes or modifications to this unit not
expressly approved by the party responsible for compliance could
void the user authority to operate the equipment.
© 2012-17 Armacost Lighting. All rights reserved.
170805
