ARM Cortex-R4 Скачать руководство пользователя страница 312 | Manualshive

Страница: 312 / 436

background image

Debug

ARM DDI 0363G

Copyright © 2006-2011 ARM Limited. All rights reserved.

12-38

ID073015

Non-Confidential

12.5.3

Lock Access Register

The DBGLAR is a write-only register that controls writes to the debug registers. The purpose
of the DBGLAR is to reduce the risk of accidental corruption to the contents of the debug
registers. It does not prevent all accidental or malicious damage. Because the state of the
DBGLAR is in the debug power domain, it is not lost when the processor powers down.

DBGLAR [31:0] contain a key that controls the lock status. To unlock the debug registers, write
a

0xC5ACCE55

key to this register. To lock the debug registers, write any other value. Accesses to

locked debug registers are ignored. The lock is set on reset.

12.5.4

Lock Status Register

The DBGLSR Register characteristics are:

Purpose

Returns the current lock status of the debug registers.

Usage constraints

The DBGLSR is:
•

a read-only register

•

only defined in the memory-mapped interface

Configurations

Available in all processor configurations.

Attributes

shows the DBGLSR bit assignments.

Figure 12-18 DBGLSR Register bit assignments

shows the DBGLSR bit assignments.

12.5.5

Device Type Register

The DBGDEVTYPE Register characteristics are:

Purpose

Indicates the type of debug component.

31

31

0

Reserved

1

2

3

32-bit access

Locked bit

Lock implemented bit

Table 12-29 DBGLSR Register bit assignments

Bits

Name

Function

[31:3]

-

Do not modify on writes. On reads, the value returns zero.

[2]

32-bit access

Indicates that a 32-bit access is required to write the key to the Lock Access Register.
This bit always reads 0.

[1]

Locked bit

Locked bit:
0 = Writes are permitted.
1 = Writes are ignored. This is the reset value.

[0]

Lock implemented bit

Indicates that the OS lock functionality is implemented. This bit always reads 1.

«
...
310
311
312
313
314
...
»

Содержание Cortex-R4





















































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для Cortex-R4

Бренд: Navitar Страницы: 1

Бренд: Swann Страницы: 6

Бренд: Swann Страницы: 4

Бренд: Cybernetyx Страницы: 4

Бренд: Waring Страницы: 8

Бренд: Kanto Страницы: 8

Бренд: DAS AUDIO Страницы: 10

Бренд: Moulinex Страницы: 6

Masterchef 5000

Бренд: Moulinex Страницы: 222

Бренд: Dash Страницы: 19

Бренд: Barco Страницы: 5

Бренд: Diamond Страницы: 5

Atmosphere AZM4

Бренд: AtlasIED Страницы: 70

Бренд: Wize Страницы: 9

Бренд: David Engineering & Mfg Страницы: 5

PDR SIDE WINDER PMSW50U

Бренд: David Engineering & Mfg Страницы: 6

Бренд: KitchenAid Страницы: 16

Бренд: KitchenAid Страницы: 20

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды