useR MANuAl
INsTAllATIoN
2
400W & 600W
ECO PANEL
HEATERS
Slimline deSign
CPIN002825
befoRe fIRsT use
Remove any promotional material and packaging from the heater.
Unwind the cord to its full length and place the heater on a firm level
surface in a stable, upright position. Visually inspect the air inlets
and outlets on the control box to ensure that there are no blockages.
To avoid overheating to a circuit do not plug the heater into
a circuit that already has other appliance working.
cAuTIoN: There may be some odour coming from the heater for the very
first time you use it. This is normal during the break-in period or after
long term storage. Make sure the heater is in a well ventilated
area and continue running it until the smell goes away.
ii. Make sure you use a drill which is suitable to the type of the wall on which
you intend to mount the heater. Drill the mounting holes at the marked
position.
iii. Insert the plastic fitting supplied with the accessory pack into the holes.
iv. Align the four mounting holes on the panel heater with the plastic fittings
and install the panel heater.
v. Screw the four fasten screws into the plastic fitting.
vi. Insert the screw caps over the screw heads.
vii. To remove the unit from wall, switch off and unplug the heater.
Remove the screw caps and unscrew the screws and remove the heater.
WAll MouNTING
Important : The heater must always be positioned so that the power
switch is located to the top right hand side of the panel when installed
either in wall mounted or free standing position. The heater is NoT
designed to be operated in any other mounting position.
i. Take into consideration the minimum required
clearance for wall mounting as indicated in
the figures below and locate the heater on
the wall.
Position the heater so that the power switch
is located to the top right hand side of the
panel. The heater is not designed to be
operated in any other mounting position.
Mark the four mounting holes to be drilled.
do not install the panel heater:
• Under a fixed mains power socket.
• In Zone 1 & 2 of bathrooms as indicated in the diagram.
• Maybe installed in Zone 3 but must be above the shaded area.
Electrical socket must not be located in the shaded area.
fReesTANdING
When using the panel heater as free
standing it must always be used with
feet assembled and in upright position.
To assemble the feet:
i. Place the panel heater on a
flat surface.
ii. Align the feet in position as shown
in the figure and tighten the fixing
screw located at the rear of the feet.
Make sure the screw is tight and the
assembly is secured.
iii. The heater is now ready for use.
NoTe: When using freestanding, keep out of traffic areas where it may be
knocked over.
The heater is equipped with a tip over switch. If the heater is knocked
over the power will be cut off automatically.
The heater panel body is hot to touch when it is operating. Turn off the
heater and allow sufficient time to cool before your relocate the panel
heater or store it.
600mm
2.50m
2.25m
600mm
400mm
150mm
Zone 1
Zone 2
Zone 3
500mm
Minimum Furniture
Clearance
500mm
300mm
2
3
4
5
6
opeRATIoN
pAINTING pANel
3
4
cAuTIoN: There may be some odour coming from the heater for the very first time you use it.
This is normal during the break-in period or after long term storage.
Make sure the heater is in a well ventilated area and continue running it until the smell goes away.
Please follow the instructions given below
i. Plug the heater into a 10 ampere wall socket.
ii. Press the On/Off Power Switch along side of the
heater to ON position to turn the heater ON.
This unit maybe painted to suit decor using water
based paints only, rated at 120°C and above.
INsTAllATIoN
1
MAINTeNANce & cleANING
5
The heater requires regular cleaning to ensure trouble free operation:
i. Unplug the heater from mains supply before cleaning.
ii. Use a wrung out (damp) cloth to wipe the exterior of the heater to remove dust and dirt.
iii. Ensure heater is dry before plugging back into the mains supply.
iv. To release the heater from the wall, for cleaning or redecoration, just open the screw bolt cap and
unscrew the screws to take off from the wall. For short term storage, just unplug the heater; for
long term storage, you can dismantle from the wall or put some protective cover over it and store
it standing upright.
four
mounting holes
feet for freestanding
option
Main oN/off
power switch
(control box
on rear)
ThIs WAy
up oNly
1
PEH208_CPIN002838.indd 2-4
19/12/13 4:05 PM
