Arkray Glucocard 01 Скачать руководство пользователя

Страница: 65 / 74

Your blood glucose level is less than 20 mg/dL or there

was not enough blood on test strip. Repeat test with new

test strip. Make sure you use enough blood to fill the strip.

If this message shows again, contact your healthcare

professional immediately!

Your blood glucose level is more than 600 mg/dL. Repeat

test with new test strip. If this message shows again,

contact your healthcare professional immediately.

Battery power is too low for testing. Replace batteries

immediately. Results may not be accurate when testing

with low battery symbol on.

Thermometer symbol. The meter temperature is outside

acceptable range of 50˚F-104˚F (10˚C-40˚C). Allow the

meter and test strips to warm up or cool down slowly

(20 minutes) until the temperature warning symbol goes

away.

Содержание Glucocard 01











































































Результаты поиска

Содержание Glucocard 01

Отзывы:

Похожие инструкции для Glucocard 01

Бренды по названию

Популярные бренды

Arkray Glucocard 01, Руководство пользователя

Результаты поиска

Содержание Glucocard 01

Отзывы:

Похожие инструкции для Glucocard 01

Бренды по названию

Популярные бренды