Ariston NUOS FS 200 Скачать руководство пользователя страница 12

Страница: 12 / 44

Set Temperature

55°C

Min. Settable Temp.

50°C

Max Settable Temp.

(with heat pump only)

55°C

Mode - Auto

On - Enabled

Mode - Boost

On - Enabled

Mode - Green

Off - Disabled

Mode - Voyage

Off - Disabled

Mode - Programs P1 & P2

P11

Off - Disabled

Programme P1 Temp.

55°C

Programme P1 Time

06:00hrs

Programme P2 Temp.

55°C

Programme P2 Time

18:00hrs

Antibacterial Function

Off - Disabled

Defrost

On - Enabled

Time_W

8 hours

3.2

URNING

NUOS O

3.3

EFAULT

ETTINGS

Display

Displays set temperature °C, mode, heat pump status and electric heater
status.

Smile Led

ON indicates NUOS is heating water.

Will also flash when system error is displayed, see 8.3.

To turn the NUOS ON and OFF, press the ON/OFF button.

The unit will turn ON in the same mode as when it was turned OFF i.e.
Auto, Boost, Green, Voyage, P1, P2 or P1+P2 (if enabled).

The NUOS has the following default settings on initial power up.

The desired temperature for the hot water is set using the ‘Control knob’ -
refer to 3.1.

The minimum temperature that can be achieved by the heat pump is
between 40°C and 50°C this limit is set by parameter P2.

The maximum temperature that can be achieved by the heat pump without
using the heater element is between 50°C and 55°C this limit is set by
parameter P3.

The maximum temperature that can be achieved using the electric heater
is 65°C.

3.4

ETTING

ESIRED

EMPERATURE

set

AUTO

Heat Pump
active

Electric Heater
active

Set
Temperature

Mode - Auto, Boost, Green, Voyage P1, P2 or P1+P2

If enabled

Installers

parameter*

Parameter

Default Setting

* See page 16

Содержание NUOS FS 200













































Результаты поиска

Содержание NUOS FS 200

Отзывы:

Похожие инструкции для NUOS FS 200

Бренды по названию

Популярные бренды

Ariston NUOS FS 200, Инструкция по установке и обслуживанию

Результаты поиска

Содержание NUOS FS 200

Отзывы:

Похожие инструкции для NUOS FS 200

Бренды по названию

Популярные бренды