GB
17
Grease/odour
fi
lter warnings
The bar at the top left
fl
ashes to indicate
that the grease
fi
lter is saturated.
The bar at the top right
fl
ashes to indicate
that the odour
fi
lter is saturated.
If both bars are
fl
ashing, then both
fi
lters
are saturated.
You must then clean/replace the grease
fi
lter (
A
) or odour
fi
lter (
B
) or both, accordingly (see “Maintenance and care”).
The latter only applies to the
fi
lter version.
To reset the
fi
lter counter:
Hold down
T4
for three seconds while the hood is on.
If both
fi
lter warnings are active at the same time, you must
reset each separately. The
fi
rst sequence resets the grease
fi
lter, while the second sequence resets the odour
fi
lter.
Con
fi
guring the hood
To set the operating mode of the hood, hold down
T4
for
6 seconds while the product is off. . After a long beep, the
type of installation displays:
Ducted
(square at bottom left
fl
ashing).
Filter
(square at
bottom right
fl
ashing).
You can change the type of
installation by pressing
T4
.
To quit con
fi
guration mode,
press
T1
once; this switches the unit off and saves the last
displayed setting.
Maintenance and care
Caution! Before cleaning or servicing the unit,
disconnect it from the mains by pulling the power plug
or disconnecting the main circuit breaker.
First cleaning
• Remove the protective
fi
lm
• Clean with a damp sponge and a little neutral soap
• Rinse off with a damp cloth
• Dry with a soft cloth; if the hood is stainless steel, dry
along the metal's grain
Periodic cleaning
The hood must be cleaned frequently (at least as often as
you service the grease
fi
lter), inside and out. Use a damp
cloth and a neutral liquid detergent with lukewarm water.
Do not use abrasive or corrosive products.
Warning:
Failure to observe the hood cleaning and
fi
lter
cleaning/replacement instructions can result in
fi
res. Follow
the instructions carefully. The manufacturer is not liable for
any damage to the motor or
fi
res caused by incorrect care
or failure to follow the above instructions.
Servicing the grease
fi
lter (A)
A
The grease
fi
lter retains the
particles of grease produced
during cooking; it must be
cleaned at least once a month
w i t h a n o n - a g g r e s s i v e
detergent, either by hand or
with a low temperature, short
dishwasher cycle.
To extract the grease
fi
lter,
pull the spring loaded handle.
If washed in a dishwasher, the metal
fi
lter may change
colour, but this does not affect its performance.
Servicing the charcoal
fi
lter (B)
The charcoal
fi
lter retains unpleasant cooking odours.
The
fi
lter saturates after a variable time, depending on the
type of cooking and how often the grease
fi
lter is cleaned.
The cartridge must be replaced at least once every twenty
months.
This
fi
lter can NOT be washed or regenerated
B
Disassembly:
Remove the
activated-carbon filter by
pressing the two front levers
which secure it to the hood.
B
Assembly:
Secure the
activated-carbon
fi
lter
fi
rst in
the back using the hood's
metal tabs and then in the
front by pressing the two
B
Содержание HGA 9.5 AM X
