background image

GB - 5

DISCLAIMER

Ariens reserves the right to discontinue, make 
changes to, and add improvements upon its 
products at any time without public notice or 
obligation. The descriptions and specifications 
contained in this manual were in effect at 
printing. Equipment described within this 
manual may be optional. Some illustrations 
may not be applicable to your unit.

DELIVERY

Customer Note: If you have purchased this 
product without complete assembly and 
instruction by your retailer, it is your 
responsibility to:

1. Read and understand all assembly 

instructions in this manual. If you do not 
understand or have difficulty following the 
instructions, contact your nearest Ariens 
Dealer for assistance. Make sure all 
assembly has been properly completed.

NOTE: To locate your nearest Ariens Dealer, 
call 1-920-756-4688 or go to www.ariens.com 
on the internet.

2. Understand all Safety Precautions 

provided in the manuals.

3. Review control functions and operation of 

the unit. Do not operate the Sno-Thro 
unless all controls function as described 
in this manual. 

4. Review recommended lubrication, 

maintenance and adjustments.

5. Review Limited Warranty Policy. 

6. Fill out a Product Registration Card and 

return the card to the Ariens Company or 
go to www.ariens.com.

SAFETY ALERTS

Look for these symbols to point 
out important safety precautions. 
They mean:

Attention!   

Personal Safety Is 
Involved!

Become Alert! 

Obey The Message!

The safety alert symbols above and signal 
words below are used on decals and in this 
manual. Read and understand all safety 
messages.

 

NOTATIONS

NOTE: General reference information for 
proper operation and maintenance practices.
IMPORTANT: Specific procedures or 
information required to prevent damage to unit 
or attachment.

PRACTICES AND LAWS

Practice usual and customary safe working 
precautions, for the benefit of yourself and 
others. Understand and follow all safety 
messages. Be alert to unsafe conditions and 
the possibility of minor, moderate, or serious 
injury or death. Learn applicable rules and 
laws in your area. Always follow the practices 
set forth in this manual.

WARNING: Improper assembly or 
adjustments can cause serious injury.

SAFETY

WARNING: To avoid injury to hands 
and feet, always disengage clutches, 
shut off engine, and wait for all 
movement to stop before unclogging 
or working on snow thrower.
Hand contact with the rotating impeller 
is the most common cause of injury 
associated with snow throwers. Never 
use your hand to clean out the 
discharge chute.

Keep hands and feet away from auger 
and impeller.

DANGER: IMMINENTLY 
HAZARDOUS SITUATION! If not 
avoided, WILL RESULT in death or 
serious injury.

WARNING: POTENTIALLY 
HAZARDOUS SITUATION! If not 
avoided, COULD RESULT in death or 
serious injury.

CAUTION: POTENTIALLY 
HAZARDOUS SITUATION! If not 
avoided, MAY RESULT in minor or 
moderate injury. It may also be used to 
alert against unsafe practices.

Содержание SNO-THRO 932037 - 724
































Отзывы: