background image

GB - 4

SAFETY ALERTS

Look for these symbols to point 
out important safety 
precautions. They mean:

Attention!   

Personal Safety Is 
Involved!

Become Alert! 

Obey The Message!

The safety alert symbols above and signal 
words below are used on decals and in this 
manual. Read and understand all safety 
messages.

 

NOTATIONS

NOTE: 

General reference information for 

proper operation and maintenance practices.

IMPORTANT: 

Specific procedures or 

information required to prevent damage to 
unit or attachment.

PRACTICES AND LAWS

Practice usual and customary safe working 
precautions, for the benefit of yourself and 
others. Understand and follow all safety 
messages. Be alert to unsafe conditions and 
the possibility of minor, moderate, or serious 
injury or death. Learn applicable rules and 
laws in your area. Always follow the practices 
set forth in this manual.

REQUIRED OPERATOR 
TRAINING

Original purchaser of this unit was instructed 
by the seller on safe and proper operation. If 
unit is to be used by someone other than 
original purchaser; loaned, rented or sold, 
ALWAYS provide this manual and any 
needed safety training before operation.

SAFETY DECALS AND 
LOCATIONS

ALWAYS replace missing or damaged Safety 
Decals. Refer to Figure 2 below for Safety 
Decal locations.

SAFETY

WARNING: 

To avoid injury to 

hands and feet, always disengage 
clutches, shut off engine, and wait 
for all movement to stop before 
unclogging or working on snow 
thrower.
Hand contact with the rotating 
impeller is the most common cause 
of injury associated with snow 
throwers. Never use your hand to 
clean out the discharge chute.
Keep hands and feet away from 
auger and impeller.

DANGER: 

IMMINENTLY 

HAZARDOUS SITUATION! If not 
avoided, WILL RESULT in death or 
serious injury.

WARNING: 

POTENTIALLY 

HAZARDOUS SITUATION! If not 
avoided, COULD RESULT in death 
or serious injury.

CAUTION: 

POTENTIALLY 

HAZARDOUS SITUATION! If not 
avoided, MAY RESULT in minor or 
moderate injury. It may also be 
used to alert against unsafe 
practices.

08000134

08000520

OS7015

1

2

3

Figure 2

Содержание Pro 28 Track









































Отзывы: