Ariens Gravely 815045 Скачать руководство пользователя страница 20

Страница: 20 / 28

EN - 18

1. Release thumb latch retaining hose to

hood assembly and remove hose from
hood assembly and blower adapter. See
Figure 30.

2. Remove mesh bags from hood assembly.

See Figure 32.

3. Remove 3/8" wing knob retaining support

strap and pull strap away from support
pin. Do not remove support pin.

4. Remove wing knob from bottom of mount

post and remove hood assembly from
unit. It is not necessary to remove hitch.
See Figure 25.

5. Remove belt cover from mower deck and

blower and idler assembly. See
Figure 21.

6. Release tension from V-belt and remove

V-belt from blower and deck spindle. See
Figure 17.

7. Remove blower assembly. See Figures

15 and 16.

Model 815049

Only

: Reinstall original

mower blades. See Figure 7.

9. Install right belt cover on mower deck. It is

not necessary to remove sheave adapter.
See Figures 5 a nd 6.

10. Remove weights and hardware and

retain. It is not necessary to remove
weight bracket. See Figure 34.

11. Ensure that mesh bags are empty, clean

and dry before storing.

BEFORE EACH USE

1. Check bagger parts for wear,

deterioration or damage. Only replace
with original service parts before
operating.

2. Make sure front weights are installed.
3. Ensure all hardware is tight.

IMPORTANT:

Check hardware often. Tighten

as needed.
4. Remove any grass buildup from bagger

parts.

5. Ensure hose is installed securely on hood

assembly and blower adapter.

6. Ensure mesh bags are installed and the

hood assembly is closed and secure
latched.

BAGGING

Starting

1. Start engine and engage PTO according

to unit owner’s manual.

2. Set throttle to full speed.
3. Set mower deck height.
4. Choose a slow ground speed.

Stopping

1. Allow the mower blades to run for at least

30 seconds to clear blower assembly and
hose of debris.

2. Disengage PTO.
3. Stop unit according to unit

Owner/Operator’s manual.

REMOVAL

WARNING:

AVOID INJURY.

Read and understand the
entire

Safety

section before

proceeding.

CAUTION:

Deflected material

may cause injury. ALWAYS
operate mower with hood
assembly closed and secured,
blower assembly fastened
securely, or with chute
deflector in operating position.

CAUTION:

Always install front

weights before operating unit
with bagger attached. Always
remove front weights when
bagger is removed from the
unit.

OPERATION

WARNING:

AVOID INJURY.

Read and understand the entire

Safety

section before

proceeding.

WARNING:

Lower attachment,

stop engine, and remove key to
prevent unauthorized use. DO
NOT park on slopes.

Содержание Gravely 815045





























Результаты поиска

Содержание Gravely 815045

Отзывы:

Похожие инструкции для Gravely 815045

Бренды по названию

Популярные бренды

Ariens Gravely 815045, Руководство оператора

Результаты поиска

Содержание Gravely 815045

Отзывы:

Похожие инструкции для Gravely 815045

Бренды по названию

Популярные бренды