manualshive.com logo in svg

Ariens Deluxe 30, Руководство по обслуживанию

Поделиться
Скачать
Ariens Deluxe 30 Скачать руководство пользователя страница 36

EN – 32

Install Traction Drive Clutch Cable

1.

Rotate unit to service position and remove bottom 
cover. See 

Service Position

 on page 7 and 

Bottom 

Cover Removal

 on page 12.

See Figure 72.

2.

Route cable end with spring hook through hole in back 
cover.

3.

Install cable end onto swing gate.

See Figure 73.

4.

Align cable with cable pulley and tighten shoulder bolt.

5.

Reconnect lower traction clutch cable to upper traction 
clutch cable.

6.

Reinstall bottom cover and secure with two tapping 
screws and four hex bolts.

7.

Reinstall upper traction clutch cable to traction clutch 
lever. Secure with one flat steel washer and hairpin. 
See Figure 69.

8.

Return unit to operating position.

9.

Adjust traction drive clutch. Refer to Operator’s 
Manual for adjustment procedure.

10. Reconnect spark plug wire and fill fuel tank.

IMPORTANT: 

Check all adjustments after first use.

WARNING: 

AVOID INJURY. Before placing unit 

in service position, drain fuel from tank and fuel 
system. See 

Draining Fuel System

 on page 7. 

Make sure unit is secure and will not tip.

Figure 72

Figure 73

Содержание Deluxe 30











































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды