Ariens Deluxe 30 Скачать руководство пользователя страница 14

Страница: 14 / 74

EN – 10

See Figure 10.

15. Remove attachment drive belts from attachment

sheave.

To assist belt removal, slowly pull recoil starter handle
while gently guiding belts out of attachment sheave.

See Figure 11.

16. Position support, such as a trash can, under

handlebars so tractor / frame remains upright when
separated from auger housing.

17. Chock or block wheels to prevent tractor / frame

movement.

See Figure 12.

18. Remove hardware securing auger housing to frame.

19. Lift auger housing rear slightly to disengage from

mount rod and separate from unit.

Reinstall Auger Housing

See Figure 13.

With assistance from an adult helper, engage
attachment clutch lever so attachment brake will not
obstruct attachment drive pulley in step 2.

Tilt auger housing rear up and lower mount brackets
onto mount rod.

WARNING:

AVOID INJURY. Attachment sheave

edges are sharp. Wear thick gloves to remove
belts from attachment sheave.

Figure 10

Figure 11

Figure 12

Figure 13

Содержание Deluxe 30











































































Результаты поиска

Содержание Deluxe 30

Отзывы:

Бренды по названию

Популярные бренды

Ariens Deluxe 30, Руководство по обслуживанию

Результаты поиска

Содержание Deluxe 30

Отзывы:

Бренды по названию

Популярные бренды