background image

2

SAFETY RULES

Safe Operation Practices for Ride-On Mowers

DANGER:  THIS CUTTING MACHINE IS CAPABLE OF AMPUTATING HANDS AND FEET AND THROW ING OBJECTS.  FAILURE 
TO OBSERVE THE FOLLOWING SAFETY INSTRUCTIONS COULD RESULT IN SERIOUS INJURY OR DEATH.

I. GENERAL OPERATION 

• 

Read, understand, and follow all instructions on the 
machine and in the manual before starting.

• 

Do not put hands or feet near rotating parts or under 
the machine. Keep clear of the discharge opening at 
all times.

• 

Only allow responsible adults, who are familiar with 
the in struc tions, to operate the machine.

• 

Clear the area of objects such as  rocks, toys, wire, etc.,  
which could be picked up and thrown by the blades.

•  Ensure the area is clear of bystanders before 

operating.  Stop machine if anyone enters the area.

• 

Never carry passengers.

• 

Do not mow in reverse unless absolutely necessary.  
Always look down and behind before and while 
back ing.

• 

Never direct discharged material toward anyone. Avoid 
discharging material against a wall or obstruction. 
Material may ricochet back toward the operator. Stop 
the blades when crossing gravel surfaces.

• 

Do not operate machine without the entire grass catcher, 
discharge chute, or other safety devices in place and 
working.

WARNING:  In order to prevent ac ci den tal 
starting when setting up, trans port ing, 
ad just ing or making repairs, al 

ways 

dis con nect spark plug wire and place 
wire where it can not contact spark plug. 

WARNING:  Do not coast down a hill in neu-
tral, you may lose control of the tractor.

WARNING:  Tow only the attachments that 
are rec om mend ed by and comply with 
spec i fi ca tions of the man u fac tur er of your 
tractor. Use common sense when towing. 
Operate only at the low est possible speed 
when on a slope.  Too heavy of a load, 
while on a slope, is dan ger ous.  Tires 
can lose trac tion with the ground and 
cause you to lose control of your tractor.

WARNING

Engine exhaust, some of its con stit u ents, and cer tain 
vehicle com 

po nents contain or emit chem 

i cals 

known to the State of Cal i for nia to cause can cer 
and birth de fects or oth er re pro duc tive harm.

WARNING

Battery posts, terminals and related ac ces so ries 
contain lead and lead compounds, chem i cals known 
to the State of Cal i for nia to cause can cer and birth 
defects or oth er re pro duc tive harm. Wash hands 
after handling.

• 

Slow down before turning.

• 

Never leave a running machine unattended.  Always 
turn off blades, set parking brake, stop engine, and 
remove keys before dismounting.

• 

Disengage blades when not mowing. Shut off engine 
and wait for all parts to come to a complete stop before 
cleaning the machine, removing the grass catcher, or 
unclogging the discharge chute.

• 

Operate machine only in daylight or good artificial 
light.

• 

Do not operate the machine while under the influence 
of alcohol or drugs.

•  Watch for traffic when operating near or crossing 

road ways.

• 

Use extra care when loading or unloading the machine 
into a trailer or truck.

•  Always wear eye protection when operating 

machine.

• 

Data indicates that operators, age 60 years and above, 
are involved in a large percentage of riding mower-
related injuries.  These operators should evaluate their 
ability to operate the riding mower safely enough to 
protect them selves and others from serious injury.

• 

Follow the manufacturer's recommendation for wheel 
weights or counterweights.

• 

Keep machine free of grass , leaves or other debris 
build-up which can touch hot exhaust / engine parts 
and burn. Do not allow the mower deck to plow leaves
or other debris which can cause build-up to occur. 
Clean any oil or fuel spillage before operating or storing 
the machine. Allow machine to cool before storage.

II. SLOPE OPERATION

Slopes are a major factor related to loss of control and 
tip-over accidents, which can result in severe injury or 
death.  Operation on all slopes requires extra caution.  If 
you cannot back up the slope or if you feel uneasy on it, 
do not mow it.
• 

Mow up and down slopes, not across.

• 

Watch for holes, ruts, bumps, rocks, or other hidden 
objects.  Uneven terrain could overturn the machine.  
Tall grass can hide obstacles.

• 

Choose a low ground speed so that you will not have 
to stop or shift while on the slope.

• 

Do not mow on wet grass. Tires may lose traction.

 

Always keep the machine in gear when going down 
slopes. Do not shift to neutral and coast downhill.

• 

Avoid starting, stopping, or turning on a slope.  If the 
tires lose traction,  disengage the blades and proceed 
slowly straight down the slope.

• 

Keep all movement on the slopes slow and gradual.  
Do not make sudden changes in speed or direction, 
which could cause the machine to roll over.

• 

Use extra care while operating machine with grass 
catchers or other at 

tach ments; they can affect the 

stability of the machine. Do no use on steep slopes.

• 

Do not  try to stabilize the machine by putting your foot 
on the ground.

• 

Do not mow near drop-offs, ditches, or embankments.  
The machine could suddenly roll over if a wheel is over 
the edge or if the edge caves in.

Содержание 936051






























































Отзывы: