Ariens 926078 Скачать руководство пользователя страница 20 | Manualshive

Страница: 20 / 34

background image

EN - 18

REPLACE SHEAR BOLTS

Replace shear bolts if obstruction stops auger
rotation and shear bolts break. See
Figure

IMPORTANT:

Ariens recommends using only

Ariens OEM shear bolts when replacing
shear bolts. See

Service Parts

1. Align shear bolt holes in auger with shear

bolt holes in the shaft.

2. Insert bolts through holes.
3. Secure bolts with nuts.
4. Tighten bolts to 7.9 N•m – 16.5 N•m

(5.8 lb-ft – 12.2 lb-ft). If a torque wrench is
unavailable, tighten bolts until they no
longer spin freely. DO NOT overtighten.

ADJUST DISCHARGE CHUTE

DEFLECTOR LEVER

If deflector does not stay in selected position,
tighten the nut under the control panel.

If deflector does not follow full range of travel:
1. Position deflector control in the rear-most

position.

2. Adjust nuts on chute cable. See

• To adjust deflector lower, loosen lower

nut and tighten upper nut.

• To adjust deflector higher, loosen upper

nut and tighten lower nut.

ADJUST DISCHARGE CHUTE

If discharge chute does not stay in selected
position:
1. Remove discharge chute gear cover.
2. Loosen rear adjustment nut and tighten

forward adjustment nut until the lock arm
engages the gear teeth.

3. Reinstall gear cover.
If discharge chute does not rotate freely:
1. Remove discharge chute gear cover.
2. Loosen forward adjustment nut and

tighten rear adjustment nut until there is
no cable slack and the lock arm engages
the gear teeth.

3. Reinstall gear cover.

Figure

26

1. Replacement Shear Bolts

Figure

27

Figure

28

1. Chute Cable
2. Upper Adjustment Nut
3. Lower Adjustment Nut

«
...
18
19
20
21
22
...
»

Содержание 926078



































Отзывы:

Нет отзывов

Похожие инструкции для 926078

Бренд: Makita Страницы: 19

Бренд: Makita Страницы: 136

Бренд: Makita Страницы: 24

Бренд: Makita Страницы: 41

Бренд: Makita Страницы: 220

Бренд: Makita Страницы: 8

Бренд: Tramontina Страницы: 28

Бренд: Eurosystems Страницы: 2

Бренд: Zenoah Страницы: 60

Бренд: Cub Cadet Страницы: 20

Бренд: Echo Страницы: 80

Бренд: Echo Страницы: 132

Бренд: Gansow Страницы: 10

Бренд: Honda Страницы: 32

Бренд: Honda Страницы: 41

Бренд: Honda Страницы: 50

Бренд: Honda Страницы: 24

Бренд: BUFFALO TURBINE Страницы: 25

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды